ABB Inora 4 Gang 2 Way 10AX Switch Royal Gold BL108-PG

Four gang means the plate contains four separate switch mechanisms. Two way means each mechanism can be connected with another compatible two-way switch so that the same circuit can be operated from two locations. The 10AX marking is a switch rating commonly used for lighting circuits and accounts for the demanding switching characteristics of certain inductive and fluorescent lighting loads. The connected load must remain within the manufacturer's rating.

Yes. The four rockers are designed to operate four separate compatible circuits from one location. For example, they can control a room's main lights, decorative lights, wall lights and balcony lights independently. Circuit design, load calculations and conductor selection should be completed by a qualified electrical professional.

Yes. Each two-way gang can be paired with a compatible two-way switch at another location, allowing a lighting circuit to be switched from either point. This arrangement is useful for staircases, corridors, bedrooms with bedside controls, large living areas and rooms with more than one entrance. Correct common and traveller-terminal wiring is essential.

It can be used with compatible LED lighting circuits when the total connected load, driver characteristics and switching inrush current are within the switch manufacturer's limits. LED drivers can create high momentary inrush currents even when their normal wattage is low. For large LED groups or commercial installations, an electrician should assess the load and use a suitable contactor or control device if required.

Installation should be performed by a licensed electrician. The supply must first be isolated and proven dead, after which the electrician should confirm the back-box compatibility and identify the circuit conductors. The common and traveller terminals should be wired according to the ABB terminal markings and the approved circuit diagram, conductors should be securely terminated, and the plate should be mounted level without overtightening. The completed installation must then be tested for polarity, insulation, continuity, earthing and correct two-way operation.

A conventional mechanical light switch normally switches the live conductor and generally does not require a neutral connection at the switch mechanism. However, the exact wiring depends on the circuit arrangement and applicable local requirements. The electrician must follow the terminal markings supplied with the BL108-PG and must never use the protective earth conductor as a neutral or switched-live conductor.

Use a compatible concealed or surface-mounted back box with sufficient depth for four switch mechanisms, cable bends and secure terminations. The box, mounting arrangement and any matching frame or accessory components must be compatible with the ABB Inora range and the site wiring system. Before ordering for a construction project, verify the plate dimensions, fixing centres, box depth and accessory compatibility against the latest ABB technical documentation.

The switch is relevant to UAE residential, hospitality and commercial projects that require a premium-finish, multi-gang lighting control point. Product selection and installation should comply with the approved project specifications, applicable UAE electrical regulations and the requirements of the relevant local authority, such as DEWA, ADDC or the authority serving the project location. Compliance and approval documents should be confirmed before use on consultant-specified projects.

It is primarily intended for suitable indoor locations. In kitchens, bathrooms, balconies, external walls or other damp and dusty areas, the installation must meet the required location, ingress-protection and safety-zone rules. Unless an appropriate IP rating is specifically documented for the complete installed assembly, use a suitably rated weatherproof or moisture-resistant accessory for exposed locations.

It should not be selected for socket outlets, water heaters, pumps, air-conditioning equipment or other heavy loads solely because it carries a 10AX marking. The rating is intended for compatible switching applications, particularly lighting circuits. Motors and high-power equipment may require a correctly rated double-pole isolator, fan controller, relay or contactor based on the equipment load and local electrical regulations.

The royal gold finish provides a decorative appearance that complements warm metallic hardware, luxury wall finishes and contemporary interior schemes. It is suitable for premium villas, hotel rooms, majlis areas, reception spaces and executive offices where electrical accessories form part of the visible design. Matching accessory finishes should be selected across the room to maintain a coordinated appearance.

Contractors should verify the model number BL108-PG, four-gang two-way configuration, 10AX rating, royal gold finish, wall-box compatibility and required quantity. They should also check approved material submittals, consultant specifications, circuit schedules, installation locations and any requirement for matching sockets, frames or blanking accessories. A sample installation is recommended on large fit-out projects to confirm finish, alignment and back-box suitability.

Isolate the circuit before inspection or maintenance. Wipe the faceplate with a soft, dry or slightly damp cloth and avoid abrasive pads, solvents, acidic cleaners or strong chemicals that could damage the royal gold finish. Loose operation, heat marks, buzzing, cracking or discolouration should be investigated promptly by a qualified electrician rather than repaired while the circuit is energized.