ABB Millenium 13A Single Pole Switched Socket Matt Gold AM23386-MG

This ABB Millenium socket is rated at 13A and 250V AC. It features a BS 13A socket outlet, single-pole switching, secure fixed-wiring terminals and flush-mounted installation. The listed overall dimensions are approximately 35 x 86 x 86 mm, and the front plate is supplied in a matt gold finish.

Yes. The UAE commonly uses 230V, 50Hz electrical systems and BS-type 13A plugs and socket outlets, making this 250V AC BS 13A socket relevant to many UAE projects. The electrician must still confirm compliance with the applicable requirements of the local authority, such as DEWA, ADDC or the relevant emirate-level utility, as well as the project's approved electrical specifications.

Single-pole switching means the socket switch interrupts the live conductor while the neutral remains connected. This provides convenient local control of a connected appliance. It is not a substitute for circuit isolation, so the distribution-board supply must be switched off, locked out where required and verified dead before installation or maintenance.

The socket is suitable for compatible BS 13A plug-equipped appliances whose operating current and starting load remain within the socket rating and the designed circuit capacity. Typical applications include televisions, computers, lamps, chargers and selected household or office equipment. High-load appliances should only be connected after an electrician verifies the appliance demand, cable size, protective device and circuit design.

Installation should be completed by a qualified electrician. The circuit must first be safely isolated and tested dead. The electrician should verify the mounting box depth and condition, identify the live, neutral and earth conductors, terminate them in the marked terminals to the manufacturer's specified torque, arrange the conductors without pinching, secure the socket level to the flush box and fit the matching frame. Final polarity, earth continuity, insulation and functional tests should be completed before energising the circuit.

Use a compatible 1-gang flush mounting box that suits the ABB Millenium assembly, the approximately 86 x 86 mm face size and the available installation depth. Box depth must allow sufficient space for the socket mechanism, conductor bend radius and safe terminal clearance. The installer should check ABB compatibility and the actual wall build-up before purchasing or fixing the back box.

Yes, provided the correct flush box and fixing method are selected for the wall construction. Concrete and blockwork installations normally require a securely embedded box with conduits positioned before plastering. Gypsum-board partitions require a suitable dry-lining box or supported metal box. In every case, the finished box should be level, firmly secured and set at the correct depth so the frame sits evenly against the wall.

Yes. Its matt gold finish is well suited to premium villas, apartments, hotel rooms, reception areas, executive offices and high-end retail interiors. Designers and contractors should coordinate the socket with matching ABB Millenium frames and accessories to maintain a consistent finish across power, lighting and low-current points.

This product should only be used where the installation location and enclosure provide the protection required by the applicable electrical regulations. Bathrooms, kitchens, balconies, gardens and other damp or exposed areas may require specific safety zones, RCD protection and a suitable IP-rated accessory or enclosure. Do not assume the decorative socket is weatherproof; ask the project electrician to assess the location before installation.

The required protective device depends on the circuit arrangement, conductor size, expected load, fault level and local regulations. Socket circuits in UAE projects commonly require appropriate overcurrent and residual-current protection, but device type and rating must be selected by the electrical designer or qualified electrician. The socket's 13A rating must not be used alone to determine the distribution-board breaker rating.

Switch off the circuit before cleaning and wipe the faceplate gently with a soft, dry or slightly damp microfibre cloth. Do not spray liquid directly onto the socket or use abrasive pads, solvents, acidic cleaners or harsh construction chemicals, as these may damage the matt gold finish. During construction, protect the accessory from paint, plaster, grout, dust and impact, but remove temporary protection according to the manufacturer's guidance.

Confirm the model number AM23386-MG, 13A and 250V AC ratings, BS 13A outlet format, 1-gang arrangement, single-pole switching, flush installation requirement and matt gold finish. Contractors should also verify back-box and frame compatibility, required quantities, approved material schedules, circuit design and local authority requirements. A project sample or mock-up is recommended where colour matching and alignment with other finishes are critical.