ABB Millenium 13A Single Pole Switched Socket Silk Black AM23386-SB

Key specifications include a rated current of 13A, rated voltage of 250V AC, BS 13A socket-outlet configuration, single-pole switching, 1-gang format and flush-mounted installation. Its stated overall dimensions are approximately 86 x 86 mm, with a depth of 35 mm. Installers should verify the wall-box depth, cable space and project requirements before installation.

Single-pole switching means the socket switch interrupts the live conductor while the neutral remains connected. This provides convenient local control of the connected appliance, but it must not be treated as complete electrical isolation. The circuit should be isolated at the distribution board and verified as de-energised before installation, inspection or maintenance.

Yes, its 250V AC rating and BS 13A socket format are relevant to the nominal 230V, 50Hz electrical supply and Type G plug system commonly used in the UAE. Final suitability depends on the project specification, connected load and applicable authority requirements. Installation should follow current UAE electrical regulations and the requirements of the relevant local authority, such as DEWA, ADDC or the authority having jurisdiction.

This socket is suitable for indoor applications such as villas, apartments, offices, hotel rooms, retail interiors and other finished construction spaces. It can serve compatible appliances and equipment whose operating current does not exceed the socket and circuit ratings. Its Silk Black finish is particularly suited to modern interiors, dark wall finishes and coordinated ABB Millenium wiring-accessory layouts.

A connected appliance must remain within the socket's 13A rating and the capacity of the complete circuit. Many air conditioners, water heaters, cookers and other fixed high-load appliances require a dedicated circuit, double-pole isolator or fused connection unit rather than a standard socket outlet. A qualified electrician should confirm the appliance starting current, cable size, protective device and manufacturer instructions before connection.

The unit is designed for flush installation in a compatible concealed wall box. After safely isolating and proving the circuit dead, a qualified electrician should confirm conductor identification, prepare the cables without damaging the insulation, connect the live, neutral and earth conductors to their marked terminals, tighten each terminal to the manufacturer's requirements and secure the socket squarely to the box. The installation should then be inspected and electrically tested before energisation.

Use a compatible 1-gang flush box that accommodates the approximately 86 x 86 mm face size and 35 mm product depth while leaving sufficient room for conductors and safe cable bending. The required box depth may increase where larger cables, conduit entries or multiple conductors are present. Confirm fixing centres and compatibility with the ABB Millenium frame or accessory arrangement before completing masonry or drywall works.

During first fix, contractors should coordinate the outlet position with architectural drawings, joinery, furniture and MEP layouts; install the correct flush box at the finished-wall depth; and protect cable entries from sharp edges. During second fix, they should check conductor condition, polarity, earthing, terminal tightness, accessory alignment and frame fit. Required continuity, insulation-resistance, polarity and protective-device tests should be completed in accordance with the approved project method and local regulations.

No. Silk Black describes the visible decorative finish and does not change the stated 13A, 250V AC electrical rating. To preserve its appearance, protect the accessory during painting, plastering and fit-out works, and clean it only with a soft, dry or lightly damp cloth. Avoid abrasive cleaners, solvents and excessive moisture.

The supplied information identifies it as a flush-mounted socket but does not state an outdoor or weatherproof IP rating. It should therefore not be assumed suitable for exposed balconies, gardens, wash areas or other damp locations. Such areas require an appropriately IP-rated enclosure or socket, suitable RCD protection and installation methods selected for the environmental conditions and UAE authority requirements.

The socket must be connected to a correctly designed circuit with suitable cable sizing, earthing and overcurrent protection. RCD or RCBO protection may also be required depending on the location, circuit design and applicable UAE regulations. Protective-device ratings must be selected for the complete circuit rather than solely from the socket's 13A rating, and the final installation should be tested by a qualified electrician.

No. The integrated single-pole switch disconnects only the live conductor and is intended for local operating control. It does not provide the same isolation as a suitable double-pole isolator or disconnection at the distribution board. For maintenance, the relevant circuit should be isolated, locked off where required and confirmed dead using appropriate test equipment.

Check the model number AM23386-SB, Silk Black colour, 1-gang configuration, frame requirements, mounting-box dimensions and fixing arrangement against the project schedule. Using matching ABB Millenium components helps maintain a coordinated appearance, but compatibility should be confirmed from current ABB technical documentation before bulk ordering for a construction project.

The ABB Millenium AM23386-SB combines a commonly used BS 13A outlet format, 250V AC rating, local single-pole control, concealed flush mounting and a contemporary Silk Black finish. These features make it relevant for premium residential, hospitality, office and retail fit-outs where reliable fixed-wiring termination and coordinated interior styling are important. Project teams should still verify approvals, specifications and local authority compliance before procurement.