ABB Millenium 13A Switched Fused Connection Unit with Flex and LED Matt Gold AM50753-MG

Isolate the supply before maintenance and wipe the faceplate with a soft, dry or slightly damp cloth. Do not use abrasive pads, solvents, acidic cleaners or harsh construction chemicals, as these may damage the matt gold surface. During building work, protect the accessory from paint, plaster, grout, dust and impact, and never allow moisture to enter the unit.

Before energising the circuit, the electrician should confirm correct line, neutral and earth termination, terminal tightness, fuse rating, flex restraint, polarity, earth continuity and insulation resistance. The switch and LED operation should then be tested, along with the relevant circuit protective device and RCD where applicable. Inspection and test records should be completed in accordance with the project and UAE authority requirements.

This ABB Millenium 13A switched fused connection unit is suited to premium residential, hospitality, office and commercial fit-out projects that require concealed wiring and a coordinated matt gold finish. It can be specified for compatible fixed appliances and building services where a 13A fused spur, local switch, flex outlet and visual status indication are required.

It can be considered for indoor locations where its electrical rating and installation conditions are suitable. No specific IP rating is provided in the listed data, so it should not be assumed to resist water, dust or outdoor exposure. For kitchens, bathrooms or utility rooms, the electrician must observe the required safety zones, moisture protection, RCD requirements and local regulations, selecting a suitably rated accessory where necessary.

No. The fuse in the FCU provides local protection for the connected appliance or flex, while the distribution-board protective device safeguards the fixed circuit against overload and fault conditions according to the electrical design. Both devices have separate functions and must be correctly coordinated by the electrical consultant or installer.

No. The connected equipment must operate within the unit's 13A and 230V AC ratings, and the fuse must be selected to protect the appliance flex and load. The circuit design must also account for cable capacity, load type, operating conditions and upstream protective devices. Motors, pumps, heaters and other loads with high starting current may require additional assessment or a different switching solution.

The listed product dimensions are approximately 42 x 86 x 86 mm. The installer should verify the compatible wall-box format and ensure sufficient internal depth for the device, conductors, flex and safe cable bending without crushing or stressing the terminals. Box selection should also suit the wall construction, whether installed in blockwork, drywall or another approved building system.

The AM50753-MG is designed for flush installation, with permanent wiring and terminals concealed inside a compatible wall box. Installation generally involves isolating and proving the supply dead, checking the box depth and cable condition, terminating line, neutral and earth conductors as marked, securing the flex with appropriate strain relief, fitting the correctly rated fuse, mounting the unit and completing electrical safety tests. This work should be carried out by a qualified electrician.

It may be used for a water heater only when the heater's rated current, starting characteristics and manufacturer instructions are compatible with a 13A fused connection unit. The electrician must calculate the load rather than relying only on the appliance type. Higher-power heaters or equipment requiring double-pole isolation, a dedicated circuit or a higher current rating need a different control device.

The integrated LED provides a visible indication of the switch or connected-circuit status. This helps users identify whether power has been switched on at the connection unit. The exact indication can depend on how the electrician terminates the unit, so the required operating logic should be confirmed during installation.

The unit is rated at 230V AC and 13A, making it suitable for many UAE low-voltage applications when specified correctly. Installation must comply with the applicable requirements of the relevant UAE electricity authority, project specifications and current electrical installation standards. A UAE-licensed electrician should confirm circuit protection, cable size, earthing, load suitability and local approval requirements before installation.

A switched fused connection unit, commonly called an FCU or fused spur, is used to connect and locally isolate fixed or semi-fixed electrical equipment from the final circuit. The flex outlet allows the appliance cable to exit neatly from the front of the unit. Typical applications may include water heaters, kitchen appliances, ventilation equipment and other compatible fixed loads, subject to the appliance manufacturer's instructions and the electrical design.

The ABB Millenium AM50753-MG is a 1-gang, flush-mounted fused connection unit designed to provide local switching and fused protection for a fixed electrical appliance or circuit. It features a flex outlet, an LED status indicator and a matt gold finish. Its rated supply is 230V AC with a maximum rated current of 13A.

Isolate the supply before maintenance and wipe the faceplate with a soft, dry or slightly damp cloth. Do not use abrasive pads, solvents, acidic cleaners or harsh construction chemicals, as these may damage the matt gold surface. During building work, protect the accessory from paint, plaster, grout, dust and impact, and never allow moisture to enter the unit.