ABB Millenium 13A Universal Switched Socket Antique Gold AM29486-AG

The ABB Millenium AM29486-AG combines a 13A universal outlet, local switched control, concealed installation and an antique gold decorative finish. It is well suited to projects requiring coordinated premium electrical accessories, particularly villas, hotels and high-end commercial interiors. For project procurement, confirm approved-brand requirements, frame compatibility, authority compliance and sample-room acceptance before placing a bulk order.

Isolate the supply before cleaning and use a soft, dry or lightly damp non-abrasive cloth. Do not apply solvents, acidic cleaners, abrasive pads or excessive water, as these may damage the decorative finish or enter the mechanism. Periodically inspect the outlet for discoloration, heat marks, looseness, damaged plug contacts or abnormal switching, and arrange professional replacement if defects are found.

Protective earthing must be correctly connected wherever required by the outlet design and the electrical installation. RCD or RCBO protection should be provided where mandated by the applicable UAE authority regulations, project specification or circuit location. The electrician must test earth continuity, polarity, insulation resistance and protective-device operation before the socket is energised.

No IP or weather-resistance rating is provided in the listed product data, so it should be treated as an indoor accessory for dry locations unless ABB documentation confirms otherwise. Installation near sinks, wet zones, bathrooms, balconies or outdoor areas requires suitable ingress protection, location clearances and circuit protection in accordance with local regulations. Use a purpose-designed weatherproof socket where moisture or dust exposure is expected.

The switch provides convenient local control of the socket outlet. However, users should not assume complete electrical isolation for maintenance unless the circuit has been isolated at the distribution board, locked off where required and proven dead with suitable test equipment. The socket switch is intended for normal operation, not as a substitute for safe isolation procedures.

The outlet must not be loaded beyond its 13A rating. At the stated maximum voltage of 250V AC, 13A corresponds to a theoretical resistive load of approximately 3,250W, but actual permitted loading depends on the appliance, supply voltage, duty cycle, cable size and protective device. High-demand or continuously operated equipment should be checked by an electrician against the circuit design and manufacturer instructions.

The flush box should be positioned level and at the approved height before plastering, tiling or decorative cladding. Allow for the final finished-wall thickness so the socket mechanism and frame sit correctly without gaps or distortion. Keep the box free from mortar, paint and debris, maintain cable protection, and verify accessibility and alignment before completing the wall finish.

The socket requires a compatible concealed wall box with sufficient depth for the mechanism, cable bend radius and safe terminal clearance. It must also be coordinated with the appropriate ABB Millenium frame or accessory system. Before wall finishing or bulk installation, contractors should confirm the box dimensions, fixing centres, frame selection and package contents against the approved product submittal.

Installation requires isolating and proving the circuit dead, confirming the correct flush box and wiring arrangement, terminating line, neutral and earth conductors at their identified terminals, securing the mechanism without trapping cables, fitting the compatible frame and testing the completed outlet. Installation must be performed by a qualified electrician in accordance with ABB instructions and applicable UAE authority requirements.

This socket is suitable for indoor locations such as villas, apartments, hotel rooms, executive offices, reception areas, meeting rooms and premium retail interiors. It can serve compatible everyday appliances and electronic equipment within its rated capacity. The antique gold finish is especially relevant where electrical accessories must coordinate with luxury interior themes, metal accents or decorative fittings.

Yes, its 250V AC and 13A ratings are suitable for many low-voltage socket applications commonly encountered in the UAE, provided the complete installation complies with the relevant emirate's electricity regulations, approved project specifications and applicable wiring standards. A qualified electrician should verify circuit protection, earthing, cable size, mounting box compatibility and plug requirements before installation.

The universal outlet is designed to accommodate multiple common plug configurations, making it useful in properties serving residents, visitors or international equipment users. Plug compatibility should still be checked before use, particularly for plug-pin shape, earthing and voltage requirements. Type G plugs are standard in the UAE, and compliant Type G connections should be preferred for permanent local use.

Key specifications include a 13A rated current, 250V AC rated voltage, universal socket outlet configuration, 1-gang format and flush-mounted installation. Its stated dimensions are approximately 35 x 86 x 86 mm. Secure cable terminals support dependable fixed-wiring connections when the socket is correctly installed and tightened to the manufacturer's requirements.

The ABB Millenium AM29486-AG is a 1-gang, flush-mounted universal socket outlet with an integrated switch for local power control. It is rated at 13A and 250V AC and features an antique gold finish suitable for premium residential, hospitality, office and commercial interiors. Its concealed wiring arrangement and compatibility with the ABB Millenium system provide a coordinated, professional wall finish.