ABB Millenium 15A Double Pole Single Switched Socket Dune Sand AM20986-DU

Switch off the circuit before inspection or cleaning. Wipe the faceplate with a soft, dry or slightly damp cloth, and avoid abrasive cleaners, solvents and excessive water. Arrange inspection by a qualified electrician if the socket becomes discoloured, cracked, loose, unusually warm, noisy or difficult to switch, as these signs may indicate damage or a poor electrical connection.

The double-pole switch provides convenient local disconnection of live and neutral for a compatible connected appliance. However, it should not automatically be treated as the sole means of safe maintenance isolation. Electrical work requires the circuit to be isolated at the appropriate distribution point, locked off where necessary and proven dead using an approved test procedure.

Conductors must be connected only to their correctly identified live, neutral and earth terminals, using the specified conductor size and terminal-tightening requirements. After installation, the electrician should carry out relevant checks such as protective-conductor continuity, insulation resistance, polarity, earth-fault protection and functional switching tests. The circuit should remain isolated until the installation has been verified as safe.

The socket's 15A rating does not itself provide overload, short-circuit or earth-leakage protection. The upstream protective device, cable size and any required RCD or RCBO must be selected according to the circuit design, connected load, installation method and local regulations. The protective device should not be chosen solely from the faceplate rating.

The socket measures approximately 35 x 86 x 86 mm and has a Dune Sand finish. Its flush-mounted format keeps fixed wiring concealed and provides a neat installed appearance. Contractors should confirm the compatible ABB Millenium frame, back box and surrounding wall-finish tolerances before procurement.

The supplied data does not state an IP protection rating, so the socket should not be assumed suitable for direct outdoor exposure, bathrooms, wash areas or other damp and dusty locations. Such environments require an appropriately rated enclosure or accessory selected for the installation zone. A qualified electrician should assess moisture, dust, temperature and local compliance requirements.

Its 250V AC rating is compatible with typical UAE low-voltage applications, subject to the approved project design and equipment plug type. Installation must comply with current UAE regulations, the relevant emirate's electricity authority requirements, project specifications and applicable standards, which may include BS 7671 where adopted. Approval should be confirmed with the consultant, contractor or authority having jurisdiction.

That depends on the connected load, project design and local authority requirements. Some 15A appliance outlets may be specified on dedicated radial circuits, while other applications may permit a different engineered arrangement. The circuit design must be determined by a qualified electrical professional and include correctly selected conductors, earthing and overcurrent and residual-current protection where required.

Contractors should verify the approved electrical drawings, load schedule, circuit voltage, maximum demand, cable conductor size, protective device rating, earthing arrangement, back-box dimensions and plug compatibility. They should also coordinate the 86 x 86 mm face dimensions and approximately 35 mm product depth with wall finishes, joinery, tiling and other services before closing the wall.

The AM20986-DU is designed for flush installation, with its wiring and mounting enclosure concealed behind the finished wall. Installation generally involves isolating the circuit, confirming the compatible back box and mounting depth, terminating live, neutral and earth conductors in the designated terminals, securing the mechanism, fitting the matching frame and completing electrical safety tests. A licensed electrician should perform the work in accordance with ABB instructions and applicable UAE requirements.

No. This model uses a 15A round-pin socket configuration and is not directly compatible with the rectangular-pin Type G 13A plugs commonly used in the UAE. Buyers should confirm the equipment plug type and project specification before ordering. Unapproved travel adaptors or plug modifications should not be used to overcome incompatibility.

The socket is intended for equipment fitted with a compatible 15A round-pin plug and operating within the outlet's 15A, 250V AC rating. Typical applications may include designated fixed-location appliances, hotel equipment and specialised residential or commercial loads. The connected appliance rating, plug configuration, circuit cable size and protective device must all be verified before use.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole switch, which normally interrupts only the live conductor. It does not replace circuit protection or safe isolation procedures during electrical installation and maintenance.

The ABB Millenium AM20986-DU is a 1-gang, 15A round-pin socket outlet with an integrated double-pole switch. Rated for up to 250V AC, it switches both live and neutral conductors for improved isolation of a compatible connected load. The unit is flush mounted, measures approximately 35 x 86 x 86 mm, and features a Dune Sand finish suitable for coordinated residential, commercial and hospitality interiors.