ABB Millenium 15A Double Pole Single Switched Socket Matt Gold AM20986-MG

Check the model number AM20986-MG, 15A current rating, 250V AC voltage rating, double-pole switched operation, round-pin connector format, 1-gang layout, flush-mounting requirement and matt gold finish against the approved material schedule. Also verify plug compatibility, mounting-box dimensions, circuit design and local authority requirements before ordering for a UAE construction or renovation project.

Switch off and isolate the circuit before maintenance. Clean the faceplate using a soft, dry or lightly damp microfiber cloth, then dry it immediately. Do not use abrasive pads, solvents, acidic cleaners, metal polish or excessive water, as these may damage the matt gold surface or enter the electrical mechanism. Loose fittings, discoloration, heat marks, buzzing or damaged contacts require inspection by a qualified electrician.

The electrician should inspect conductor identification and terminal tightness, confirm protective-earth continuity and test insulation resistance, polarity, circuit protection and functional double-pole switching. Where applicable, RCD or RCBO operation and earth-fault protection should also be verified. Results should be recorded as part of the project's inspection and testing documentation before handover.

The supplied information does not state an ingress-protection rating, so it should be treated as an indoor product for dry locations unless ABB documentation confirms otherwise. Installation near water, outdoors or in damp and dusty areas requires an appropriately rated enclosure, correct electrical zoning and compliance with local regulations. A qualified electrician should assess kitchens, bathrooms, balconies and external locations before use.

Yes, provided a compatible flush box and the correct construction method are used. Drywall installations require a secure cavity box or suitable support, while blockwork and concrete installations require a properly aligned embedded box and protected conduit. The box should be set flush with the final wall finish so the frame sits level without gaps, distortion or pressure on the wiring.

No. The complete circuit must be assessed rather than relying only on the socket rating. Actual suitability depends on the equipment load, duty cycle, cable capacity, circuit breaker or fuse, ambient temperature, installation method and manufacturer instructions. Continuous or high-load equipment should be checked by a qualified electrical engineer or electrician before connection.

The product requires a compatible concealed box suitable for its 86 x 86 mm face dimensions and approximately 35 mm product depth, with additional space allowed for conductors and terminal clearance. Cable size, conductor type and protective device must be selected according to the connected load, installation method, ambient conditions, voltage-drop calculation and applicable UAE wiring requirements. Confirm box compatibility and installation depth using the ABB technical documentation before wall preparation.

Installation should be completed by a licensed electrician after isolating and proving the circuit dead. The installer should use a compatible flush mounting box, route the conductors without damaging insulation, connect live, neutral and earth to the identified terminals, tighten terminals to ABB's specified torque, secure the mechanism level with the finished wall and fit the matching frame. Electrical testing must be completed before energising the circuit.

Yes, it can be specified for villas, apartments, hotels, offices, retail units and other fit-out projects where a 15A round-pin outlet is required. Its flush-mounted design conceals fixed wiring, while the matt gold finish complements premium decorative schemes. The electrical consultant should verify outlet type, load schedule, circuit protection and authority compliance before procurement.

It is intended for compatible equipment fitted with the corresponding 15A round-pin plug and whose electrical load does not exceed the socket, circuit or protective-device rating. Applications may include selected lighting circuits, dedicated equipment and installations specified by consultants. It should not be used with a standard UAE Type G plug unless a properly engineered and approved connection arrangement is provided.

The socket is rated at 250V AC and is compatible with the UAE's nominal 230V, 50Hz supply when used within its stated current rating. However, its round-pin format is not the standard BS 1363 Type G outlet commonly used for general-purpose sockets in the UAE. Contractors should confirm plug compatibility, project specifications and the requirements of the relevant local authority before installation.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole switch, subject to correct circuit design and installation. The protective earth conductor remains permanently connected and must not be switched.

This switched socket has a rated current of 15A, a rated voltage of 250V AC and a 15A round-pin outlet configuration. It is designed for concealed flush installation and measures approximately 86 x 86 mm with a stated depth of 35 mm. The unit includes secure terminals for fixed wiring and a matching finished frame.

The ABB Millenium AM20986-MG is a 1-gang, flush-mounted 15A round-pin socket outlet with an integrated double-pole switch. It switches both live and neutral conductors for improved circuit isolation and features a matt gold finish suitable for premium residential, hospitality and commercial interiors.