ABB Millenium 15A Double Pole Single Switched Socket Mocha Brown AM20986-MO

Keep the faceplate dry and clean it only with a soft cloth; avoid abrasive products, solvents and direct water spray. Periodically check for loose mounting, discoloration, overheating, cracking, arcing sounds or an unreliable switch. Stop using the outlet and have it inspected by a licensed electrician if any damage, heat or abnormal operation is detected.

Confirm that the required outlet is a 15A round-pin type, the circuit voltage is compatible with the 250V AC rating, and a double-pole switched configuration is specified. Also verify the 86 x 86 mm dimensions, back-box depth, ABB Millenium frame compatibility, mocha brown colour, quantity required and any consultant, authority or project approval requirements.

Set out the outlet location using the approved electrical drawings, furniture layouts, appliance connection points and accessibility requirements. Coordinate the back box before blockwork closure, plastering, tiling or gypsum-board finishing, and allow clearance for the plug and cable. Protect the mechanism from cement, paint and construction dust, then install the finished accessory after wet trades are complete.

Do not assume suitability for wet, dusty or outdoor locations because an IP rating is not stated in the supplied specifications. In kitchens, bathrooms, plant areas or external locations, verify zoning, ingress-protection and enclosure requirements with the project consultant and local regulations. Use an appropriately rated weatherproof accessory where exposure to water, condensation, dust or harsh conditions is possible.

Yes. It must be connected to a correctly designed earthed circuit with suitable overcurrent protection and, where required by UAE regulations or the installation location, residual-current protection. The socket's switch is for local control and double-pole isolation; it does not replace the distribution-board protective device or safe lockout and verification procedures.

No. The complete installation must be assessed, including the appliance load, duty cycle, plug compatibility, cable size, circuit length, ambient temperature, grouping, protective device and local derating requirements. At 230V, 15A corresponds to about 3.45kW in simple resistive-load terms, but this is not a universal appliance allowance. An electrical engineer or licensed electrician should verify the actual design load.

Yes, provided a suitable flush box and approved installation method are used. For concrete or blockwork, the box should be securely set at the correct finished depth before final plastering or tiling. For gypsum-board partitions, use an appropriate dry-lining box or supported mounting arrangement. Coordinate the wall opening, box alignment and final finish during construction to achieve a level 86 x 86 mm installation.

Use a flush back box with adequate depth and fixing points for the 86 x 86 mm accessory and its approximately 35 mm product depth, while allowing additional room for cable bends and terminals. Confirm compatibility with the ABB Millenium mechanism, matching frame and wall-box system before ordering. Cable size, earthing arrangement and protective device must be selected by the project electrician according to load, installation method and local regulations.

This product is designed for flush mounting, with the wiring and suitable wall box concealed behind the finished wall surface. A licensed electrician should isolate the supply, confirm the circuit is dead, prepare the compatible back box, terminate live, neutral and earth conductors at the marked terminals, secure the mechanism without trapping cables, fit the compatible frame or cover, and complete polarity, earth-continuity, insulation and functional tests before energising.

Its 250V AC rating is suitable for use with the UAE's nominal 230V, 50Hz supply, subject to correct circuit design and local approval requirements. Installation should follow the current UAE electrical regulations and the requirements of the relevant authority, such as DEWA, ADDC or the applicable emirate utility, together with project specifications and manufacturer instructions.

The socket is intended for compatible equipment fitted with the correct 15A round-pin plug and operating within the outlet, cable and circuit ratings. Potential applications include selected fixed-location appliances, workshop equipment, commercial installations and designated power points in residential or hospitality projects. Confirm the appliance load, plug pattern and project specification before installation; it is not a standard UAE Type G rectangular-pin outlet.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole switch, although it does not replace isolation at the distribution board before electrical installation, inspection or maintenance.

Key specifications include a 15A rated current, 250V AC rated voltage, 15A round-pin outlet, double-pole switching, 1-gang configuration and flush-mounted installation. Its listed dimensions are approximately 86 x 86 mm, with a depth of 35 mm. Model AM20986-MO is supplied in a mocha brown finish.

The ABB Millenium AM20986-MO is a 1-gang, flush-mounted 15A round-pin socket outlet with an integrated double-pole switch. It is rated at 250V AC and switches both live and neutral conductors for improved circuit isolation. The mocha brown finish suits coordinated residential, commercial and hospitality interiors.