ABB Millenium 45A Cooker Control Unit with 13A Switched Socket Antique Gold AM118147-AG

Confirm the model number AM118147-AG, 45A and 250V AC ratings, 2-gang configuration, BS 13A switched socket, antique gold finish and flush-mounting requirement. Buyers should also verify the cooker load, compatible ABB Millenium frame, back-box dimensions and depth, cable space, project approvals and required quantities against the electrical and architectural schedules.

Isolate the circuit before cleaning and use a soft, dry or lightly damp cloth. Do not use abrasive pads, strong solvents, acidic cleaners or excessive water, as these may damage the antique gold surface or enter the electrical mechanism. Periodic inspection by a qualified electrician is advisable if the switch becomes loose, warm, discoloured or difficult to operate.

The installer should inspect terminal tightness, conductor identification, earthing, cable support and faceplate alignment, then complete the electrical tests required by the applicable installation standard and local authority. The cooker load and protective-device rating should be checked against the approved design, and both the cooker switch and 13A socket should be functionally tested.

It may be used where the approved electrical schedule calls for a 45A cooker control switch with a 13A switched socket. Commercial kitchens can involve higher loads, three-phase equipment, increased heat, moisture or specialised isolation requirements, so the consultant must confirm suitability. Contractors should also coordinate mounting depth, containment, cable access and decorative finishes before wall completion.

Yes, it can suit residential kitchens, premium villas, apartments and hospitality fit-outs where a 45A cooker control point, BS 13A auxiliary socket and antique gold finish are specified. Compatibility with the appliance load, distribution board, wiring system, wall box, ABB Millenium accessories and project finish schedule should be confirmed before purchase.

Cable size and protective-device rating cannot be selected from the switch rating alone. They depend on cooker load, circuit length, voltage drop, installation method, ambient temperature, grouping, conductor material and local regulations. A qualified electrical designer or contractor should calculate the circuit and ensure that the protective device, cable and 45A switch are correctly coordinated.

The internal arrangement and required circuit connections must be determined from the ABB wiring information and the approved electrical design. The 13A outlet must remain properly protected, while the cooker connection must be sized for the calculated cooking-appliance load. An electrician should not assume circuit configuration from the front layout alone.

Its 250V AC rating and BS-format 13A socket configuration are relevant to electrical systems commonly used in the UAE. However, product selection and installation must also comply with the applicable UAE wiring regulations, local authority requirements, approved project specifications and any required certification. The electrical contractor should verify approval for the specific emirate and project before installation.

It should be readily accessible for normal operation and emergency isolation, but it should not be positioned where heat, steam, water or cooking activity could create a hazard. The final location must follow the kitchen layout, appliance manufacturer's instructions, approved electrical drawings and the requirements of the relevant UAE authority and project consultant.

This is a flush-mounted 2-gang device designed to coordinate with the ABB Millenium system. Before ordering, check the listed dimensions of 42 x 147 x 86 mm, terminal space, cable bending requirements and compatibility with the chosen ABB frame and concealed back box. High-current cooker cables can require additional box depth and installation space.

Installation should be completed by a qualified electrician with the supply isolated and verified dead. The electrician should confirm back-box compatibility and depth, route and terminate the fixed wiring securely, connect line, neutral and earth conductors according to the product markings and approved circuit design, fit the compatible ABB Millenium frame, and test polarity, continuity, insulation resistance and protective-device operation before energising.

Not automatically. Suitability depends on the appliance manufacturer's connected-load data, diversity calculations where permitted, supply voltage, cable size, installation method and circuit protection. A qualified electrician should confirm that the complete circuit and the 45A control unit are appropriate for the selected appliance.

No. The 13A switched socket is intended for a suitable plug-connected appliance within its rated capacity. The electric cooker or hob should be supplied through the dedicated 45A cooker circuit, subject to the appliance load, cable size, protective device and project electrical design.

The unit is rated at 45A and 250V AC and incorporates a cooker control switch and a BS 13A switched socket outlet. It is intended for flush mounting, has an overall listed size of 42 x 147 x 86 mm, and uses secure terminals for fixed-wiring connections. The model number is AM118147-AG.