ABB Millenium 45A Cooker Control Unit with 13A Switched Socket Black Glass AM118147-BG

Confirm the model number AM118147-BG, 45A and 250V AC ratings, BS 13A switched socket requirement, 2-gang arrangement, listed dimensions of 42 x 147 x 86 mm, flush-box compatibility, wall depth, and matching ABB Millenium frame or accessories. The project electrician should also confirm that the specified cooker load, cable, circuit protection, and local authority requirements are compatible with the unit.

Isolate the circuit before cleaning, then use a soft, lightly damp cloth on the black glass surface. Avoid abrasive pads, strong solvents, excessive water, and chemical cleaners that may damage the finish or enter the mechanism. Periodic electrical inspection should be carried out if there are signs of overheating, discoloration, loose operation, cracking, arcing, or an unusual smell.

The electrician should inspect terminal tightness, conductor identification, earthing continuity, polarity, insulation resistance, protective-device operation, and functional switching. The cooker circuit and 13A socket should be tested according to the approved installation procedure, and the glass plate should sit level without cracks, chips, or excessive fixing pressure. Test results should be recorded where required by the project consultant or local authority.

It should be installed where it is protected from water, condensation, direct heat, grease, and impact. Separation from sinks and cooking surfaces must follow the approved kitchen layout, manufacturer guidance, and applicable UAE electrical rules. If the planned location is exposed to moisture or excessive heat, the electrician should select a safer position or a product with environmental protection appropriate to that location.

No. The 45A figure is the documented current rating of the cooker control switch, not the appliance's continuous consumption. Actual current depends on the cooker's power rating, operating mode, supply voltage, and circuit design. The switch rating must be adequate for the designed load, but it does not replace proper load calculations or protective-device coordination.

The unit is designed for flush installation and may be incorporated into suitable masonry, blockwork, or drywall systems using a compatible concealed box and mounting arrangement. Contractors should coordinate the box depth, cable entry, wall finish, frame dimensions, and final alignment before closing the wall. Adequate space must be retained so that conductors are not sharply bent, compressed, or damaged behind the mechanism.

The control should be readily accessible for local isolation but positioned away from direct heat, steam, water, and cooking splashes. It should not be concealed behind the cooker or placed where operating it requires reaching across a hot surface. The exact mounting location and height should follow the kitchen layout, project specifications, appliance instructions, accessibility needs, and local electrical requirements.

Yes, its 250V AC rating and BS 13A socket format are relevant to typical UAE low-voltage residential installations, subject to project and authority requirements. It is suitable for villas, apartments, staff accommodation, and selected commercial kitchen fit-outs when the circuit design matches the connected appliance. Approval and installation requirements should be checked against the applicable rules of the local authority, such as DEWA, ADDC, SEWA, or the relevant emirate's utility provider.

Cable size and protective-device rating cannot be selected from the 45A switch rating alone. The electrician must consider the cooker's connected load, installation method, cable length, ambient temperature, grouping, voltage drop, fault protection, and any applicable diversity calculation. The final cable, MCB or RCBO, earthing arrangement, and residual-current protection must comply with the appliance instructions and relevant UAE electrical regulations.

Installation requires a compatible concealed wall box, correctly sized fixed wiring, suitable circuit protection, secure terminal connections, and the matching ABB Millenium mounting components. The supply must be isolated and verified dead before work begins. After termination, the unit should be aligned in the box, secured without stressing the glass face, and tested before energisation. Installation should be completed by a licensed or qualified electrician.

The BS 13A switched socket provides a convenient outlet for a suitable plug-connected kitchen appliance. It should only be used with correctly fused BS-type plugs and loads within the socket rating. The circuit arrangement and anticipated simultaneous load must be assessed by an electrician to prevent overloading.

It is intended for fixed high-load cooking equipment such as compatible electric cookers, built-in ovens, and hobs. Suitability must be confirmed from the appliance nameplate, connected load, manufacturer instructions, circuit voltage, and design current. A qualified electrician should calculate the load rather than selecting the control unit solely from the appliance type.

The unit has a rated current of 45A, a rated voltage of 250V AC, and an integrated BS 13A switched socket outlet. It uses a flush-mounted configuration with secure terminals for fixed wiring. The listed overall dimensions are 42 x 147 x 86 mm, and the product is designed to coordinate with compatible ABB Millenium frames and accessories.

The ABB Millenium AM118147-BG is a flush-mounted, 2-gang cooker control unit combining a 45A cooker control switch with a BS 13A switched socket outlet. It provides convenient local isolation for a fixed cooking appliance while offering a separate socket for an appropriate 13A plug-connected appliance. Its black glass finish is suitable for contemporary residential and commercial kitchen interiors.