ABB Millenium 45A Cooker Control Unit with 13A Switched Socket Matt Gold AM118147-MG

Key specifications include a 45A rated current, 250V AC rated voltage, integrated BS 13A switched socket outlet, two-gang configuration and flush-mounted installation. The listed overall dimensions are approximately 42 x 147 x 86 mm. Installers should verify the mounting-box dimensions, terminal capacity and compatible ABB Millenium frame before installation.

A 45A control unit is commonly used on dedicated cooker circuits, but suitability depends on the appliance nameplate load, diversity calculation, circuit cable size, installation method, ambient temperature, protective device and manufacturer instructions. A qualified electrician must calculate the design current and confirm that every circuit component is correctly coordinated; the switch rating alone does not determine circuit suitability.

The integrated BS 13A switched socket is intended for compatible plug-in appliances within its rated capacity, such as a cooker hood or small kitchen appliance where permitted by the electrical design. It must not be used to supply a high-load cooker that requires a dedicated fixed connection. Socket placement and use should also account for heat, moisture and accessibility.

It is relevant to UAE villas, apartments, staff accommodation and suitable commercial kitchen support areas that use 250V AC low-voltage installations and BS-style 13A accessories. Project consultants and contractors should confirm the approved material schedule, authority requirements and appliance load before specifying it. Acceptance may depend on the applicable emirate, development, consultant and utility regulations.

Installation should be completed by a licensed electrician with the upstream supply safely isolated, locked off where required and proven dead. The installer should use a compatible flush back box and ABB Millenium frame, route the dedicated cooker-circuit conductors without damaging insulation, connect line, neutral and protective earth conductors to the identified terminals, tighten them to ABB's specified torque, refit the faceplate and complete the required electrical tests before energising.

This is a two-gang, flush-mounted accessory, so it requires a compatible concealed wall box with adequate depth for the device, conductors and safe cable bending. The listed product dimensions are approximately 42 x 147 x 86 mm, but the exact back-box format and depth should be checked against the ABB installation instructions and Millenium frame configuration before wall cutting, blockwork chasing or final fit-out.

Cable size cannot be selected from the 45A accessory rating alone. It must be calculated using the cooker load, circuit length, voltage drop, installation method, grouping, thermal insulation, ambient temperature, protective-device rating and applicable diversity rules. The selected conductors must also fit the terminals correctly. Final cable sizing should be performed by the project's qualified electrical engineer or electrician.

The electrician should inspect conductor identification, terminal tightness, protective-earth continuity and polarity, then perform the tests required for the completed circuit. These may include continuity, insulation resistance, polarity, earth-fault loop impedance and RCD or RCBO operation where applicable. Functional operation of both the cooker switch and 13A switched socket should be confirmed before handover.

Keep the unit dry and clean it only with a soft cloth; avoid solvents, abrasive products and excessive moisture. Periodically check for heat discolouration, cracking, loose operation, buzzing, burning odour or damaged socket contacts. If any fault is noticed, isolate the circuit and have a qualified electrician inspect the terminals, wiring and protective device rather than attempting a live repair.

Contractors should verify the model number AM118147-MG, 45A and 250V AC ratings, BS 13A switched socket format, two-gang layout, flush-mount requirement, dimensions, matt gold finish and compatibility with the selected ABB Millenium frame and back box. They should also compare it with the approved material submittal, electrical load schedule, cooker manufacturer requirements and local authority specifications.

The matt gold finish suits premium residential kitchens, hospitality interiors and coordinated fit-out projects commonly specified in the UAE. It can be matched with compatible ABB Millenium frames and accessories for a consistent appearance. During construction, protect the faceplate from cement dust, paint, abrasive cleaners and metal tools to preserve the finish.

Installation directly behind a cooker or hob is generally undesirable because the control may become inaccessible and exposed to heat. The unit should normally be located in an accessible position adjacent to the cooking appliance while maintaining suitable separation from hot zones and sinks. The final location must be approved against the appliance instructions and project electrical layout.

It should be readily accessible for local control without requiring a user to reach over the hob or another hot surface. It should not be installed where heat, steam, water splashes or appliance movement could create a hazard. Exact positioning must follow the kitchen layout, appliance manufacturer's instructions, consultant drawings and applicable UAE electrical and building requirements.

The ABB Millenium AM118147-MG is a flush-mounted cooker control unit combining a 45A cooker control switch with a BS-type 13A switched socket outlet. It is designed for convenient local control of a suitably rated fixed cooker circuit while providing an additional socket for compatible 13A appliances. The matt gold finish coordinates with compatible ABB Millenium frames and accessories.