ABB Millenium 5A Double Pole Single Switched Socket Black Glass AM22186-BG

This product uses a 5A round-pin connection and is intended for designated low-current applications, often where controlled lighting or a specific appliance connection is required. Standard UAE general-purpose outlets commonly use the BS 1363 rectangular-pin format and are typically rated at 13A. The plug types are not interchangeable, and adapters should not be used to bypass the socket's intended rating or circuit design.

Switch off the circuit before cleaning, then wipe the faceplate with a soft, dry or slightly damp non-abrasive cloth. Avoid solvents, abrasive pads, excessive water and direct spray around the switch or socket openings. If there is cracking, discoloration, looseness, overheating or intermittent operation, isolate the circuit and arrange inspection by a qualified electrician.

Confirm the model number AM22186-BG, 5A current rating, 250V AC rating, double-pole switching, 1-gang configuration, 5A round-pin connector, black glass finish and flush-mount dimensions. Also verify the compatible back box and frame, plug type, project quantities, approved material submittal, circuit schedule and compliance requirements for the relevant UAE authority.

At the nominal UAE supply of 230V, a 5A rating corresponds to a theoretical maximum of approximately 1,150W for a simple resistive load. Actual suitability can be affected by inrush current, power factor, operating conditions and circuit design. The connected equipment's nameplate current and manufacturer instructions must therefore be checked, and the 5A rating must never be exceeded.

Yes, the terminal arrangement is designed to support dependable fixed-wiring connections when conductors are correctly prepared, inserted and tightened to the manufacturer's specified torque. Loose terminals can cause overheating or failure, so cable condition and terminal tightness should be checked by a qualified installer during commissioning.

Do not assume this standard flush-mounted unit is weatherproof or suitable for wet locations because no IP rating is stated in the supplied specifications. Bathrooms, wash areas, balconies and outdoor installations require equipment with the correct ingress protection, zoning compliance and additional protection specified by local regulations. Use this socket in dry indoor locations unless ABB documentation and the approved design confirm otherwise.

Yes, it can be specified for villas, hotel rooms, offices and other commercial interiors where a controlled 5A round-pin outlet is required. Its black glass finish suits premium interior schemes, while flush mounting provides a neat appearance. Contractors should verify connector compatibility, circuit schedules, authority requirements and consultant approval before procurement.

Cable size and protective-device selection must be determined from the connected load, installation method, conductor length, voltage drop, ambient temperature, grouping and local authority rules. The circuit protection must prevent the socket from being loaded above 5A. A qualified electrical engineer or electrician should follow the approved project design rather than selecting cable size from the socket rating alone.

Isolate and verify the circuit is dead, prepare a compatible flush box, route the specified conductors and terminate them at the marked terminals in accordance with ABB instructions and the approved wiring diagram. Secure the mechanism without trapping cables, fit the matching frame and black glass faceplate, then complete polarity, continuity, insulation-resistance, earthing and functional tests before energising. Installation should be carried out by a qualified UAE electrician.

The stated product dimensions are 35 x 86 x 86 mm, with an 86 mm face width. It is intended for flush mounting, which keeps the fixed wiring and compatible wall box concealed behind the finished wall surface. Confirm the back-box size, available depth and fixing arrangement before ordering or installation.

Its 250V AC rating is compatible with the nominal 230V, 50Hz supply commonly used in the UAE. However, a 5A round-pin outlet is not the usual BS 1363 general-purpose socket format, so it should be installed only where the project specification calls for this connector type. Installation must comply with applicable UAE electrical regulations, the relevant emirate authority requirements and the consultant-approved design.

The socket is suitable only for compatible round-pin plugs and loads that do not exceed its 5A, 250V AC rating. Typical applications may include controlled lighting, lamps and other designated low-current equipment, subject to the approved circuit design. It must not be used for high-load appliances such as kettles, heaters, ovens or air-conditioning equipment.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete circuit isolation than a single-pole switch, although it does not replace isolation at the distribution board before inspection, maintenance or electrical work.

The ABB Millenium AM22186-BG is a 1-gang, 5A round-pin socket outlet with an integrated double-pole switch and a black glass finish. Rated at 250V AC, it is designed for flush-mounted fixed wiring and provides local control of a compatible low-current electrical load.