ABB Millenium 5A Double Pole Single Switched Socket Stainless Steel AM22186-ST

The key specifications are a 5A rated current, 250V AC rated voltage, 5A round-pin socket configuration, double-pole switching, 1-gang format and flush-mounted installation. The overall stated dimensions are 35 x 86 x 86 mm, with an 86 mm face width. Installers should verify the wall box depth, terminal space and complete ABB Millenium system compatibility before installation.

Double-pole switching disconnects both the live and neutral conductors when the socket is switched off. This provides more complete local isolation than a single-pole arrangement, which normally switches only the live conductor. It does not replace circuit protection or the required safe-isolation procedure during electrical maintenance.

This outlet is intended for compatible low-current equipment fitted with the correct 5A round-pin plug, such as selected lamps, lighting circuits and controlled appliances within the circuit design. The connected load must not exceed the 5A rating, and suitability should be confirmed from the appliance nameplate, plug type and project electrical schedule.

No. A 5A round-pin socket has a different pin configuration and substantially lower current capacity than the commonly used 13A rectangular-pin socket. It should only replace an outlet where the wiring design, protective device, back box, appliance plug and project specification all require a 5A round-pin connection. Do not use improvised plug adapters or modify pins to make an incompatible appliance fit.

In UAE villas, apartments, hotels and commercial interiors, 5A round-pin outlets may be specified for table lamps, bedside lighting or other controlled low-current loads. Their distinct plug format helps separate designated lighting or managed circuits from general-purpose 13A outlets. Actual use must follow the approved electrical drawings, load schedule and requirements of the relevant UAE authority.

This is a flush-mounted wiring accessory, so the suitable concealed wall box and cable route should be prepared before final wall finishing. A qualified electrician must isolate and prove the circuit dead, verify the conductors, terminate them at the correctly marked terminals, confirm secure connections, mount the mechanism level and fit the compatible frame or cover. The circuit must then be tested before energisation. Installation should follow the ABB instructions, the approved project specification and applicable UAE electrical regulations.

Contractors should confirm the 1-gang opening, wall box dimensions and depth, cable entry position, conductor size, earth continuity, terminal clearance and compatibility with the matching ABB Millenium frame. Allow sufficient space so conductors are not sharply bent or trapped behind the mechanism. The finished wall surface should be level to prevent distortion or uneven gaps around the stainless steel face.

The concealed back box and conduit are normally installed during first-fix electrical work. Cable termination and the socket mechanism are completed during second fix after major plastering, tiling or wall finishing. The decorative stainless steel surface should remain protected from cement, paint, grout, abrasive dust and impact until final cleaning and handover.

The circuit requires protective devices and cable sizing selected by the electrical designer according to the connected load, installation method, fault level and applicable regulations. The socket's 5A rating does not by itself determine the required MCB, fuse or RCD arrangement. UAE projects should follow approved drawings and the rules of the relevant authority, such as DEWA or the applicable emirate utility, together with project-adopted standards such as BS 7671 where specified.

No IP rating is stated in the supplied product information, so it should not be assumed suitable for wet, exposed or outdoor locations. Installation in bathrooms, kitchens or other areas exposed to moisture must comply with the applicable electrical zones and require suitable ingress protection. For gardens, balconies, plant rooms or wash areas, use a properly rated weatherproof accessory or enclosure specified by the electrical consultant.

Clean the visible surface with a soft, dry or lightly damp non-abrasive cloth after isolating the circuit. Avoid acidic cleaners, chlorine products, solvents, steel wool and abrasive pads, as these can stain or scratch the finish. In coastal or dusty UAE environments, regular gentle cleaning helps prevent deposits, but the product should not be treated as weatherproof unless an appropriate IP rating is separately confirmed.

A qualified electrician should perform the tests required by the project and local regulations, including protective-conductor continuity, insulation resistance, polarity and operation of the double-pole switch. Terminal security and the circuit protective device should also be checked. The outlet should only be energised after satisfactory results are recorded in the relevant inspection and testing documentation.

The product information states that a matching frame completes the installed finish, but package contents should be confirmed before ordering because ABB Millenium mechanisms, frames and related components may be supplied separately depending on the listing. Check that the selected frame has the correct finish, module arrangement and compatibility with model AM22186-ST.

Compare model AM22186-ST with the approved material submittal, socket schedule and consultant specification. Confirm the required 5A round-pin connector, 250V AC rating, double-pole switched operation, 1-gang flush format, stainless steel finish and stated 35 x 86 x 86 mm dimensions. For substitutions or large UAE construction projects, obtain consultant approval and verify current ABB technical documentation before procurement.