طلاء بنجالاك الأبيض غير اللامع سعة (18L)

الميزات والفوائد

إنه يوفر لمسة نهائية قوية غير لامعة. خالية من المعادن الثقيلة الخطرة مثل الزئبق والرصاص والكادميوم والزرنيخ والكروم وغيرها.

الاستخدامات الموصى بها: مثالي لتغطية السطح الداخلي.

يمكن استخدامه أيضًا لتغطية المباني الخارجية الخشبية والفولاذية.

الأسطح المناسبة للطلاء

جص أسمنتي ، خرسانة ، خشب ، فولاذ .

التطبيق

يمكن للمرء استخدام المنتج مع العناصر التالية: يوصى باستخدام الأسطوانة

الرذاذ: استخدم الرذاذ التقليدي أو البخاخ الخالي من الهواء.

ينصح باستخدام الفرشاة لطلاء الزوايا والحواف.

بيانات المنتج

أحجام العبوات: 18 لتر.

المواد الصلبة بالحجم: 47 ± 2 حجم٪ نظري. الثقل النوعي: 1.45 نظري فقط للون الأبيض. المركبات العضوية المتطايرة: 403 جم / لتر ISO 11890 EU

تعليقات المركبات العضوية المتطايرة: القيمة النظرية

ستتغير القيمة المختبرة بناءً على منهجية الاختبار ودقة معدات الاختبار وبيئة الاختبار.

TECHNICAL DATA

Airless spray:

Nozzle tip 0.018–0.021".

Spray angle degrees 65–80°.

Pressure at nozzle 150 Kg/cm² (2100 psi).

Film thickness per coat.

Typical recommended range,

Dry film thickness 30 - 40 µm

Wet film thickness 65 - 85 µm.

Film thickness will vary and is calculated as average.

Theoretical spreading rate 15.7 - 11.8 m²/l

Spreading speed is affected by the amount of applied film, the type of texture, the porosity of the surface, flaws, temperature, and painting waste, among other factors. At the thinnest dry film thickness, the maximum spread rate per coat is obtained, and vice versa.

Thinner: Jotun Thinner No. 2.

Dilution: Maximum 10 %.

Filler: Stucco - 2 Coats.

Topcoat: Bengalac Matt - 2 Coat(s).

CONDITIONS DURING APPLICATION

The substrate's temperature must be at least 10 °C and at least 3 °C above the air's dew point, as measured close to the substrate. To guarantee adequate drying in small spaces, good airflow is typically needed. No more than 4% of the substrate's moisture should be present (by weight). Once the coating is entirely dried, it should not be subjected to mechanical stress, oil, or chemicals.

DRYING TIMES

Drying times are typically influenced by factors like air flow, temperature, film thickness, and number of coats.

The advice given is to repaint using the same type of general paint.

If more than one coat is applied, the number, order, and total thickness of the prior applications applied will all affect drying timeframes.

Prior to applying the next layer, the surface needs to be dry and clear of any contaminants.

The following values are used to calculate drying time:

Relative Humidity (RH) 50 %

Substrate temperature: 10 °C 23 °C 40 °C.

Surface (touch) dry: 18 h 8 h 6 h.

Hard dry: 48 h 24 h 18 h.

Dry to over coat, minimum: 48 h 24 h 18 h.

GUIDELINES FOR USE

SURFACE PREPARATION

The substrate needs to be sturdy, spotless, dry, and devoid of debris, oil, grease, lacquer, etc. Form release agents and curing agents must be completely eliminated. Before application, a little sanding with the appropriate abrasive material is advised. Any resulting dust or loose debris must be taken out.

Recommended painting technique:

PVA Primer or Fenomastic Emulsion Primer: 1 Coat.

Other paint systems.

On wooden surfaces:

Bengalac Wood primer: 1 Coat

Stucco: 2 Coats

Bengalac Matt: 2 Coats

On steel surfaces:

Bengalac Red Oxide Primer: 1 Coat

STORAGE

The product must be stored in compliance with national regulations. Keep the containers away from heat sources and ignition sources in a dry, cool, well-ventilated area. Containers must be kept shut. Use caution when handling.