PowerSafe Gun LED Floodlight 100W Daylight PSLED FLGS100 DL

This floodlight can be considered for construction sites, building perimeters, workshops, warehouses, loading areas, compounds, driveways, gardens and other spaces requiring wide-area illumination. Its suitability depends on the required lighting design, mounting location, environmental conditions and available electrical supply. It should not be used in submerged locations or in environments exceeding the manufacturer's stated operating conditions.

A colour temperature of 6500K produces a cool, crisp white light commonly described as daylight. This appearance can support visibility in work areas, access routes, yards and security-lighting applications. It is cooler and visually whiter than warm-white or neutral-white lighting, so buyers should confirm that 6500K matches the intended atmosphere and project lighting schedule.

The stated IP65 rating makes the enclosure dust-tight and resistant to water jets when the floodlight is correctly installed with suitable sealed connections. This supports use in many exposed UAE locations, but IP65 does not mean the fitting can be submerged. Installation should also account for high ambient temperatures, direct sunlight, airborne dust, coastal salinity, drainage and the protection of cables, glands and junction boxes.

The floodlight is rated for a 220–240V AC supply at 50/60Hz, which is compatible with commonly used UAE low-voltage installations when connected correctly. The circuit, cable size, protective device, earthing arrangement and isolation method must be selected according to the connected load, cable route and applicable authority requirements. A qualified electrician should verify the actual supply before energising the unit.

Isolate and verify the electrical supply before installation. Secure the floodlight bracket to a structurally sound surface using fixings suitable for the substrate, such as concrete, blockwork or steel. Aim the fitting without obstructing heat dissipation, route the cable safely and complete the connection through appropriately rated glands and enclosures. Restore power only after checking terminal security, earthing, sealing, mounting stability and circuit protection. Installation should be carried out by a qualified electrician.

Contractors should check the mounting height, coverage area, glare, shadows, access for maintenance and the strength of the supporting structure. Fixings must suit the base material and withstand vibration and expected wind exposure. Outdoor cable entries and junction boxes should maintain an appropriate ingress-protection level, while cable routes should be protected from impact, sharp edges, standing water and active construction operations.

No. The PowerSafe PSLED FLGS100 DL is specified as non-dimmable and should not be connected to a conventional dimmer. If automatic operation is required, use only a compatible switching device, timer, contactor or sensor with ratings suitable for LED loads and inrush current. Compatibility should be confirmed before installation to avoid flickering, unreliable switching or equipment damage.

Under the IP classification convention associated with IEC 60529, the first digit 6 indicates a dust-tight enclosure, while the second digit 5 indicates protection against water jets. The installed system is only as well protected as its cable glands, joints, seals and junction boxes. The rating does not cover immersion, and it can be compromised by damaged seals, loose covers or incorrect installation.

The required quantity cannot be determined from wattage alone. A lighting calculation should consider the area's dimensions, mounting height, fitting positions, surface reflectance, beam distribution, required illuminance, obstructions and maintenance factor. For construction work areas, access routes or commercial premises, the project engineer should set the target lux level and verify the layout using confirmed photometric data for the fitting.

It may be used in a properly designed temporary lighting installation where its voltage, mounting and environmental ratings are appropriate. The fitting must be securely mounted rather than left loose, and its supply should include suitable isolation, earthing and circuit protection. Temporary cables and connections must be protected against machinery, vehicles, water and physical damage in accordance with project safety procedures and applicable UAE electrical requirements.

It may be switched by a compatible motion sensor or photocell if the control device is designed for the supply voltage and the electrical characteristics of LED loads. The sensor's switching capacity, inrush-current capability and environmental rating should be checked, especially for outdoor installations. Where several floodlights are controlled together, a suitably rated contactor may be required.

Isolate the power and allow the fitting to cool before inspection or cleaning. Remove dust from the lens and housing with a soft cloth and an appropriate non-abrasive method; avoid harsh chemicals and high-pressure cleaning directed at seals or cable entries. Periodically inspect the bracket, fasteners, cable, glands, junction box and enclosure seals for looseness, corrosion, cracking or damage. Maintenance frequency should be increased on construction sites and in dusty or coastal locations.

Installation should follow the manufacturer's instructions, the project's approved electrical specifications and the requirements of the relevant UAE authority or utility. Depending on the emirate and project, this may include local wiring regulations, municipality requirements and site-specific consultant approvals. A qualified electrical professional should confirm circuit protection, earthing, cable selection, outdoor connections, isolation and inspection before commissioning.

Check the complete model reference PSLED FLGS100 DL and SKU 83490-NOS against the project schedule or replacement unit. Confirm the required 100W rating, 6500K daylight colour, 220–240V AC 50/60Hz supply, IP65 rating and non-dimmable operation. If replacing another fitting, also verify mounting dimensions, connection arrangement, physical clearance and required lighting performance before ordering.