PowerSafe Round LED Panel Light 24W Daylight PSLEDR PL24 DL

This model has a rated power of 24W, a 6500K daylight colour temperature and a 220–240V AC, 50/60Hz electrical input. It uses LED lighting technology and is identified by model number PSLEDR PL24 DL and SKU 83684-NOS. Confirm the product dimensions, driver arrangement, cut-out requirement and other project-specific details before installation.

A 6500K colour temperature produces a cool, crisp daylight appearance. This light colour can improve visual clarity in work-focused spaces such as offices, utility rooms, workshops, retail areas, corridors and building service rooms. Buyers seeking a warm or neutral ambience should choose a lower colour temperature instead.

Yes. Its stated 220–240V AC, 50/60Hz input is compatible with the nominal low-voltage supply commonly used in the UAE. The circuit, protective device, wiring and connections must still comply with applicable UAE regulations and the requirements of the relevant local authority.

It may be used in compatible indoor lighting installations, including apartments, villas, offices, shops, reception areas, corridors, kitchens, utility spaces and selected commercial or construction applications. Suitability depends on the ceiling system, required illumination level, environmental conditions and approved project lighting design.

Isolate and verify the electrical supply before work begins. Confirm that the ceiling opening or mounting system is compatible, connect the supplied or specified LED driver according to its wiring instructions, secure all terminals, position the driver safely and mount the panel without trapping cables. The installation should then be inspected and tested before energising. A qualified electrician should carry out the work.

It can replace an existing fitting when the supply voltage, mounting method, ceiling opening, available recess depth, driver space and circuit conditions are compatible. Do not assume that two round lights use the same cut-out size. Measure the existing opening and verify the PowerSafe panel dimensions before ordering or modifying the ceiling.

No. The supplied product data identifies this model as non-dimmable. It should be connected to a standard compatible on/off lighting circuit rather than a conventional dimmer. Using an incompatible dimming control may cause flickering, unreliable operation or damage to the driver.

Contractors should check the approved lighting layout, required lux level, panel and ceiling compatibility, cut-out size, recess clearance, driver location, circuit load, switching arrangement and maintenance access. They should also verify any project requirements for emergency lighting, fire-rated ceilings, ingress protection, glare control and authority approvals, as these features are not confirmed by the basic product data.

Only install it in such locations if the product documentation confirms an appropriate IP rating and the installation complies with the relevant electrical zones and environmental requirements. No specific IP rating is stated in the supplied data, so it should not be assumed to be weatherproof, waterproof or dustproof. Use a suitably rated fitting for exposed, wet or high-dust locations.

The required quantity depends on room dimensions, ceiling height, surface reflectance, layout, task type and target illuminance. For construction and commercial projects, a lighting calculation should be completed using the manufacturer's confirmed lumen output and photometric data. Wattage alone is not sufficient to determine the number of panels needed.

The 24W value indicates nominal electrical power consumption, not the exact light output. Brightness must be assessed using the confirmed lumen rating, beam distribution and installation conditions. Request or review the manufacturer's photometric information when precise lighting performance is required for an engineering specification.

Installation should follow the current requirements of the relevant UAE electricity authority, applicable local electrical regulations, project specifications and recognised wiring practices. The circuit should include appropriate isolation and protection, and connections should be enclosed and accessible as required. Approval requirements can differ by emirate and project, so the responsible contractor or consultant should verify the applicable rules.

Do not cover the panel or LED driver with thermal insulation unless the manufacturer explicitly permits it. Maintain the specified clearance around the fitting and driver, avoid contact with hot services, and keep wiring away from sharp edges and mechanical damage. Coordination with HVAC ducts, fire systems and ceiling supports is important during construction.

Switch off and isolate the circuit before cleaning or inspection. Use a soft, dry or lightly damp cloth on accessible surfaces and avoid abrasive cleaners, solvents or direct water spray. Check periodically for flickering, discolouration, loose mounting or driver noise. Electrical faults and component replacement should be handled by a qualified technician.