PowerSafe Slim Square LED Panel Light 40W Daylight 60 x 60 2-Piece Pack PSLEDS PLS40 DL 60 x 60

Switch off and isolate the circuit before inspection or cleaning. Use a soft, dry cloth and avoid water, solvents or abrasive materials. Periodically check for loose mounting, discolouration, flicker, overheating or damaged wiring. Electrical faults and component replacement should be handled by a qualified electrician using compatible parts and in accordance with the manufacturer’s guidance.

Confirm the model number PSLEDS PLS40 DL 60X60, nominal 60 x 60 format, 40W power rating, 5200-lumen output, 6500K daylight colour, 220–240V AC supply, non-dimmable operation, IP20 protection and two-piece pack quantity. Contractors should also verify exact dimensions, mounting compatibility, accessory requirements and acceptance against the project submittal before ordering.

The supplied specifications do not identify this model as a self-contained emergency luminaire. It should not be treated as an emergency fitting unless it is used with a manufacturer-approved emergency conversion system and the complete installation is designed, tested and certified for the project’s emergency-lighting requirements.

The listed colour rendering index is greater than 80. A CRI above 80 is generally suitable for routine office, retail, educational and commercial lighting where natural-looking colour distinction is required. Applications involving precise colour inspection may require a higher-CRI fitting specified by the project consultant.

The stated rated lifetime is 25,000 hours under the manufacturer’s specified operating conditions. Service life can be affected by ambient temperature, ventilation, supply quality, switching frequency and installation conditions. Adequate clearance around electrical components and operation within the stated ratings can help support reliable performance.

Each panel has a nominal rated power of 40W, so the two-piece pack represents 80W of connected lighting load before considering driver characteristics, power factor, inrush current and circuit diversity. The electrical designer should size cables, protective devices, switching equipment and control components using complete manufacturer data and applicable UAE electrical regulations.

The required number cannot be determined from floor area alone. A lighting designer or electrical engineer should consider the target lux level, room dimensions, mounting height, working-plane height, surface reflectance, maintenance factor and panel photometric data. The listed output of 5200 lumens per panel can support an initial calculation, but a proper lighting layout is recommended before installation.

SKU 83710-PKT contains two PowerSafe 40W slim square LED panel lights. For project procurement, calculate quantities by individual panel rather than by pack alone, and include any approved spare allowance required by the contractor, consultant or facilities team.

The PowerSafe PSLEDS PLS40 DL 60X60 is a slim, square LED panel light designed for compatible indoor ceiling installations. Each panel is rated at 40W and produces a listed luminous output of 5200 lumens with a 6500K daylight colour appearance. It operates on 220–240V AC at 50/60Hz, carries an IP20 rating and is supplied as a two-piece pack.

IP20 indicates protection against access by fingers and solid objects larger than approximately 12.5 mm, but it does not provide rated protection against water. The panel is therefore intended for suitable dry indoor locations. It should not be installed outdoors or in wet, exposed, high-condensation or wash-down areas unless an appropriately rated enclosure and installation design are specified by a qualified professional.

No. This model is specified as non-dimmable and should not be connected to a conventional wall dimmer or lighting control output that varies the supply voltage. Use a standard compatible switched circuit unless the manufacturer provides an approved alternative control arrangement.

Not automatically. The 60 x 60 description identifies the nominal panel format, but ceiling grids and openings can vary between projects. Before procurement or cutting an opening, check the product’s exact external dimensions, recess requirements, driver or connection clearance, ceiling load capacity and required mounting accessories. This is particularly important in fit-out and refurbishment work.

Installation should be completed by a qualified electrician. Isolate and verify the electrical supply, inspect the fitting and connection components, confirm the ceiling opening and support arrangement, connect the panel only to a compatible 220–240V AC 50/60Hz circuit, secure all wiring and position the panel correctly. Restore power only after electrical testing and inspection. Always follow the manufacturer’s instructions and applicable UAE authority requirements.

The nominal 60 x 60 format is commonly associated with modular suspended ceiling grids, but compatibility must be checked against the actual panel dimensions, ceiling opening, grid system, available void depth and mounting method. The ceiling frame must support the fitting safely, and any project-required safety restraints should be installed in accordance with the ceiling manufacturer’s instructions and local requirements.