PowerSafe Standard LED Strip Light 7W Daylight Single Line 100m Roll PSLED SLSS 07W 1L DL 100M

This LED strip produces 6500K daylight, which appears as a crisp, cool-white light. It is commonly selected for work areas, utility spaces, workshops, service corridors, site facilities and other locations where clear visibility is preferred over a warm decorative ambience.

The available product information states a nominal 7W rating but does not confirm whether this is measured per metre, per defined section or for another operating length. Before calculating the lighting load or selecting a driver, ask FEPY to confirm the wattage basis shown on the product label or technical datasheet.

The required operating voltage and driver specification are not provided in the listed data. Verify the voltage marked on the strip before installation and use only a compatible LED driver, rectifier or power connection system recommended for this model. The strip must not be connected directly to the UAE mains supply unless its manufacturer documentation explicitly confirms that it is designed for direct mains operation.

Cut the strip only at the manufacturer-marked cutting points. Cutting elsewhere can damage the circuit or leave a section inoperative. Use compatible connectors, end caps and power leads, observe any indicated polarity, and electrically insulate every termination. Do not assume that the full 100m roll can be powered from one end; the permitted run length and power-injection intervals must be confirmed from the manufacturer instructions.

Plan the route and operating sections before cutting, isolate the electrical supply, prepare a clean and stable mounting surface, and install the strip using its specified fixing method or a suitable LED profile. Complete connections with compatible accessories, protect joints from mechanical damage, and test each section before closing ceilings, joinery or access panels. Final electrical work should be carried out by a qualified electrician.

It may be installed in a compatible aluminium profile if the profile dimensions suit the strip width and connector arrangement. A profile can provide straighter installation, physical protection and improved heat management, while a suitable diffuser can reduce visible LED spotting. Confirm dimensional compatibility and ventilation requirements before ordering profiles for the project.

No. The listed product attribute identifies this model as non-dimmable. It should not be connected to a dimmer unless PowerSafe provides written confirmation of a compatible control system, as an unsuitable dimmer or driver may cause flickering, unstable operation or premature failure.

Indoor or outdoor suitability depends on the strip's IP rating, insulation system, connectors and installation method. An IP rating is not stated in the supplied specifications, so it should not be assumed to be waterproof or suitable for exposed outdoor locations. For gardens, façades, wet areas or dusty construction environments, verify the required IP rating and use weather-resistant housings, joints and accessories approved for the location.

The 6500K daylight output is relevant to UAE commercial, industrial and residential projects where cool-white task or utility lighting is required. Typical applications may include workshops, stores, service areas, temporary project facilities, coves and linear details. Designers should still confirm the project lighting schedule, required lux levels, glare control and client-approved colour temperature.

Installation should comply with the applicable UAE electrical regulations, project specifications and the requirements of the relevant local authority or utility, such as DEWA or the corresponding authority in the project emirate. A qualified electrician should verify cable sizing, circuit protection, earthing where applicable, driver accessibility, isolation and maximum connected load before energising the system.

Do not operate the complete roll as one continuous run unless the manufacturer's technical instructions specifically permit it. Long LED strip runs can experience voltage drop, uneven brightness, overheating or excessive current. Divide the roll into approved section lengths and provide correctly rated drivers or power-injection points based on the confirmed voltage, wattage and maximum-run specification.

Confirm the model number PSLED SLSS 07W 1L DL 100M, 100m roll length, 6500K daylight colour, strip width, operating voltage, wattage basis, cut interval, maximum run length, IP rating and required driver or connector system. Contractors should also compare these details with the approved material submittal, reflected ceiling plan, lighting schedule and bill of quantities.

Avoid installing the strip on hot, dusty, damp or poorly prepared surfaces. Keep it away from direct heat sources and use a compatible aluminium profile where heat dissipation or mechanical protection is required. Drivers should be ventilated, accessible for maintenance and operated within their rated ambient temperature. Outdoor or unconditioned installations require additional verification of temperature and ingress-protection ratings.

Subject to voltage, IP and installation compatibility, it can be considered for linear lighting in coves, shelves, cabinets, counters, corridors, utility rooms, workshops, retail displays and architectural details. For emergency lighting, fire-rated assemblies, hazardous areas or life-safety applications, use only products specifically certified and approved for that purpose.