PowerSafe Bubble Solar LED Floodlight 300W Daylight PSLED SFLBS300 DL

This solar LED floodlight can be considered for construction compounds, site access areas, villas, gardens, boundary walls, parking spaces, pathways, farms, warehouses and other outdoor locations with sufficient sunlight. The required illumination level, mounting position, operating time and site conditions should be assessed before selection.

A 6500K colour temperature produces a cool, bright white appearance commonly described as daylight. It supports clear visibility in outdoor work areas, entrances, pathways and security-focused locations. It is cooler in appearance than warm white lighting and may not be suitable where a softer decorative ambience is preferred.

Solar floodlights are relevant to the UAE because of the country's strong solar exposure, but suitability depends on the product's confirmed ingress-protection rating, operating-temperature range and installation environment. Before using the unit in exposed, coastal, dusty or high-temperature locations, verify these ratings in the manufacturer documentation and install it where ventilation and maintenance access are available.

Install the solar panel in an open position receiving direct sunlight for most of the day, away from buildings, trees, scaffolding and other sources of shade. The panel should be securely mounted and oriented according to the manufacturer's instructions. Dust accumulation can reduce charging performance, so periodic cleaning is especially important in UAE conditions.

Select a structurally sound wall, pole or approved support, mark the fixing points and use fasteners suitable for the substrate and expected wind load. Mount the floodlight and solar components as shown in the supplied instructions, adjust the beam toward the required area and keep any cables protected from sharp edges, heat and water collection points. A competent installer should complete the work and confirm secure fixing and correct operation.

Confirm that the concrete is sound and free from concealed electrical cables, pipes and reinforcement at the proposed drilling points. Use correctly sized anchors and corrosion-resistant fasteners appropriate for the fitting weight and exposure conditions. The bracket must be firmly secured, and the installation should account for vibration, wind loading and safe maintenance access.

It may be used for suitable outdoor construction areas such as access routes, storage zones, temporary compounds and perimeter locations. However, it should not be treated as the sole source of safety-critical or emergency illumination unless the complete lighting design and product certification support that use. Contractors should verify lux requirements, operating duration, mounting stability and compliance with the relevant UAE authority and project specifications.

The 300W figure is the manufacturer's stated product rating for model PSLED SFLBS300 DL, but wattage alone does not establish brightness. For lighting calculations, buyers should also verify the rated lumen output, beam angle, mounting height, battery capacity, solar-panel rating and expected operating duration from the current product datasheet.

No. The listed specification identifies this model as non-dimmable. It should not be connected to an external dimmer or incompatible control device. Any automatic operating modes or controls should be used only as described in the manufacturer's instructions.

The correct mounting height depends on the required coverage, beam characteristics, surrounding obstructions and target illumination level. Higher mounting can increase coverage but may reduce light intensity at ground level. For construction and commercial applications, a lighting professional should determine the position using the verified lumen output, beam angle and required lux level.

A solar floodlight is intended to obtain charging energy from its solar system, which can make it useful where mains power is unavailable or difficult to route. The exact component arrangement and connection method must be confirmed from the supplied manual. Do not connect the unit directly to a mains circuit unless the manufacturer specifically provides and approves that configuration.

Installation should follow the manufacturer's instructions, applicable UAE electrical and building requirements, project specifications and the rules of the relevant local authority, such as DEWA, ADDC or SEWA where applicable. The installer should also confirm secure structural fixing, cable protection, outdoor environmental suitability and safe access for inspection and maintenance.

Inspect and clean the solar panel regularly with a soft cloth and a suitable non-abrasive method, particularly after dust storms. Check the floodlight lens, bracket, anchors, cables and connections for dirt, looseness, corrosion or damage. Isolate the unit before maintenance and follow the manufacturer's cleaning and battery-service instructions.

Operating time can be reduced by inadequate daytime charging, shade, dust on the solar panel, seasonal changes in sunlight, high ambient temperatures, frequent activation or battery ageing. Check that the panel is clean and unobstructed and allow a complete charge cycle as directed. If performance remains low, have the battery and associated components inspected using the manufacturer's specifications.