PowerSafe Designer LED Bulb 7W Daylight E14 PSLEDB DS 0714 DL

The bulb has a rated power of 7W, an E14 cap, a 6500K daylight output and a 220-240V AC operating range at 50/60Hz. It uses LED technology, has a standard bulb shape and is non-dimmable. The exact model reference is PSLEDB DS 0714 DL, and the FEPY SKU is 83349-NOS.

This bulb requires an E14 small Edison screw lamp holder. Before ordering or installation, confirm that the existing luminaire is marked E14 and supports a 220-240V LED lamp. It will not fit larger E27 holders, bayonet holders or GU-type sockets without an appropriate approved fitting.

A 6500K colour temperature produces a cool, crisp white light commonly described as daylight. It is suitable for utility spaces, workshops, store rooms, service areas and task-oriented locations where a bright-looking visual environment is preferred. Buyers seeking a softer yellow appearance should select a warm-white lamp instead.

Yes. Its stated 220-240V AC, 50/60Hz rating is compatible with the nominal low-voltage supply commonly used in the UAE. The luminaire, wiring, switchgear and protective devices must also be correctly rated, and installation must comply with the requirements of the relevant UAE electricity authority and project specifications.

No. This model is non-dimmable and should be connected to a standard on/off lighting circuit. Using it with a conventional dimmer, electronic lighting controller or incompatible smart switch may cause flickering, unstable operation, noise or premature failure.

Switch off and isolate the lighting circuit, then allow the existing lamp to cool before removal. Confirm that the holder is E14, dry, undamaged and rated for 220-240V operation. Screw the bulb into the holder gently until secure without overtightening, restore power and test it. Fixed wiring work should be completed by a qualified electrician in accordance with applicable UAE authority requirements.

Yes, it can be specified for compatible E14 decorative and general lighting fixtures in residential, commercial and fit-out projects. Contractors should verify the approved lighting schedule, cap type, colour temperature, fixture dimensions, electrical rating and non-dimmable requirement before procurement. For consultant-controlled projects, submit the product details for approval before bulk installation.

It can be used in compatible table lamps, wall lights, decorative fittings, display fixtures, corridor lights, utility-area luminaires and selected ceiling fittings. Suitability depends on the luminaire's E14 holder, voltage rating, available internal space, ventilation and environmental protection.

Use it outdoors only when installed inside a properly enclosed, weather-resistant luminaire rated for the location. The product information does not state an IP rating for the bulb itself, so it should not be exposed directly to rain, irrigation water, dust or high humidity. This is particularly important for UAE gardens, balconies, façades and external service areas.

Use in an enclosed fitting only if the luminaire manufacturer confirms compatibility with a 7W E14 LED bulb. Adequate heat management is important because high ambient temperatures and trapped heat can reduce LED service life, especially in UAE buildings, plant rooms and non-air-conditioned spaces.

The connected steady-state load can be estimated by multiplying 7W by the number of bulbs, but circuit design must not be based on wattage alone. A qualified electrician should consider LED driver inrush current, cable capacity, protective-device rating, switching capacity, voltage drop and any local authority or project requirements.

First confirm that the fitting uses an E14 screw holder. Then check the luminaire's internal clearance and maximum permitted lamp wattage. Although the bulb has a standard shape, buyers should compare the available space and fitting restrictions before purchase, particularly for compact decorative shades and enclosed fixtures.

Possible causes include a loose lamp holder, incompatible dimmer, unsuitable electronic switch, unstable supply, poor wiring connection or a faulty fitting. Isolate the circuit before checking the bulb and holder. If flickering continues in a standard on/off circuit, have the installation inspected by a qualified electrician.

Verify model PSLEDB DS 0714 DL, 7W rating, E14 cap, 6500K daylight colour, 220-240V AC supply and non-dimmable operation against the bill of quantities, approved material schedule and fixture data. A sample installation is recommended to confirm physical fit, visual appearance and control compatibility before project-wide procurement.