PowerSafe Gun LED Floodlight 150W Daylight PSLED FLGS150 DL

This LED floodlight is suitable for illuminating construction sites, building exteriors, warehouses, workshops, loading areas, parking spaces, compounds, gardens and other compatible commercial or residential areas. The mounting location, required coverage and local lighting requirements should be assessed before installation.

Its IP65 rating makes the correctly installed enclosure suitable for outdoor areas exposed to dust and water jets. However, it must not be submerged or installed where water can continuously collect. For UAE outdoor use, installers should also provide weatherproof cable entries, suitable junction boxes and secure mounting appropriate for local heat, dust and wind conditions.

A 6500K colour temperature produces a cool white, daylight-like appearance that supports clear visibility in work and security areas. It is commonly selected for construction zones, yards, workshops and service areas where practical illumination is preferred. It may appear brighter and cooler than warm white lighting used for decorative or relaxed spaces.

The floodlight is rated for a 220-240V AC supply at 50/60Hz, which is compatible with commonly used UAE low-voltage electrical systems when correctly connected. The circuit, cable size, isolator and protective devices must be selected according to the connected load, installation conditions and applicable authority requirements.

Isolate the electrical supply, select a structurally sound mounting surface and securely fix the floodlight using fasteners suitable for the substrate. Set the required beam direction without obstructing ventilation, route the cable through appropriate weather-resistant accessories and complete the electrical connection according to the manufacturer’s requirements. A qualified electrician should test earthing, polarity, insulation and operation before the circuit is energised.

It may be mounted on a compatible concrete, masonry or steel support when the structure and fixing method can safely carry the fitting and withstand vibration and wind loads. Use anchors or bolts appropriate for the base material, avoid damaging reinforcement or concealed services and protect steel fixings against corrosion. Temporary construction-site mounting must remain stable and comply with site safety procedures.

No. IP65 refers to the stated protection of the floodlight enclosure when it is correctly installed and maintained. Cable joints, glands, junction boxes and isolators require their own suitable ingress-protection ratings. The fitting is not designed for immersion, and the IP protection can be reduced by damaged seals, loose entries or incorrect installation.

No, this model is specified as non-dimmable. It should not be connected to a conventional dimmer or incompatible lighting-control output. It can be switched through a suitably rated manual switch, contactor, timer or sensor only when that equipment is compatible with LED loads and the floodlight’s electrical characteristics.

A compatible motion sensor or photocell may be used if its voltage, switching capacity and LED-load rating suit the floodlight. LED drivers can have a higher startup current than their normal operating current, so the control device should be selected accordingly. Installation and testing should be carried out by a qualified electrician.

The required quantity depends on the area dimensions, mounting height, beam distribution, surface reflectance, obstructions and target illumination level. A lighting layout or lux calculation is recommended for construction work zones, access routes, storage yards and parking areas. Do not determine the quantity from wattage alone, as the product data provided does not state lumen output or beam angle.

It can be considered for compatible permanent exterior or site lighting where its electrical rating, IP65 protection and light output meet the project design. The engineer or contractor should verify the required lux level, mounting arrangement, emergency-lighting obligations and environmental conditions. Temporary supplies and portable-site applications may require additional protection and equipment.

Installation should follow the current UAE electrical regulations, project specifications and requirements of the relevant local authority or utility in the emirate, such as DEWA or the applicable Abu Dhabi, Sharjah or Northern Emirates authority. Suitable earthing, circuit protection, cable selection, isolation and outdoor-rated accessories must be provided by a qualified electrical professional.

Mount the fitting securely and direct the beam toward the intended working surface rather than nearby roads, windows or neighbouring properties. Avoid aiming it directly into the line of sight of workers, drivers or pedestrians. For UAE construction and commercial projects, the final position should support the required illumination while limiting glare, spill light and unnecessary upward light.

Isolate the power before maintenance and periodically remove dust from the lens and housing with a soft, dry or lightly damp cloth. Inspect the mounting hardware, cable glands, seals, wiring and enclosure for looseness, corrosion or damage. Do not use abrasive materials, pressure washing or solvents, and have any electrical fault examined by a qualified electrician.