PowerSafe Gun LED Floodlight 50W Daylight PSLED FLGS50 DL

This floodlight is suitable for lighting construction work areas, building exteriors, compounds, entrances, loading areas, workshops, warehouses, parking spaces, pathways and residential outdoor areas, subject to a site-specific lighting and electrical assessment. The mounting position, required illumination level and environmental conditions should be checked before installation.

Its IP65 rating supports use in exposed areas where dust and water jets may be present, making it relevant to many UAE exterior-lighting applications when correctly installed. However, IP65 does not mean the fitting is submersible. The installer should also consider direct sunlight, high ambient temperature, coastal salinity, wind-blown dust and the manufacturer's permitted operating conditions.

An IP65 enclosure is classified as dust-tight and protected against water jets under the applicable ingress-protection test conditions. Effective protection depends on correct mounting, intact seals and properly rated cable glands, junction boxes and terminations. The floodlight should not be installed underwater or in areas requiring a higher IP classification.

The specified 6500K colour temperature produces a cool, daylight-white appearance. This can support visibility in work zones, service yards, workshops and security-lighting areas where a crisp visual environment is preferred. Buyers should confirm that 6500K is appropriate for the project specification, neighbouring properties and intended occupancy.

Installation should be carried out by a qualified electrician. Isolate and verify the electrical supply, secure the fitting to a structurally sound surface, aim it without obstructing ventilation, connect it to a compatible 220–240V AC supply and use weather-resistant glands and junction accessories where exposed. Restore power only after checking polarity, earthing where required, insulation, sealing and mechanical security. Always follow the supplied manufacturer instructions and local authority requirements.

The floodlight is rated for 220–240V AC at 50/60Hz, which is compatible with commonly used UAE low-voltage supplies when the circuit is correctly designed. The electrician must verify the actual site voltage and provide suitable cable sizing, isolation, earthing and overcurrent and residual-current protection according to the installation conditions and applicable regulations.

No. The PSLED FLGS50 DL is specified as non-dimmable and should not be connected to a conventional dimmer or incompatible lighting controller. If automatic operation is required, use a suitably rated external timer, photocell, contactor or occupancy sensor only after confirming electrical compatibility, switching load and manufacturer requirements.

The quantity cannot be determined from wattage alone. A lighting plan should consider the area's dimensions, mounting height, beam distribution, surface reflectance, obstructions, required lux level and shadow control. Because lumen output and photometric data are not stated in the available product information, contractors should obtain these details or conduct a site trial before finalising quantities for safety-critical construction lighting.

The correct height and angle depend on the area, required coverage and approved mounting arrangement. Position the fitting to spread light across the target zone while limiting glare, dark spots and direct light into roads, neighbouring buildings or occupants' eyes. Use secure structural fixings appropriate for the substrate, and do not exceed the mounting limitations stated by the manufacturer.

IP65 alone does not establish suitability for pool zones, marine exposure or highly corrosive environments. Pool installations require special electrical zoning and protection, while coastal locations may require enhanced corrosion-resistant materials and more frequent maintenance. A qualified electrical designer should assess the location and applicable UAE authority requirements before use.

The designer should calculate the total connected load using the 50W nominal rating of each unit and account for cable length, installation method, voltage drop, ambient temperature, grouping, fault protection and LED-driver inrush current. Circuit breakers, residual-current protection, isolators, contactors, cables and enclosures must be appropriately rated for the complete installation rather than selected from wattage alone.

Installation should comply with the project specification, manufacturer instructions and the regulations of the relevant UAE electricity and building authority, such as the applicable requirements in Dubai, Abu Dhabi or the respective emirate. IP classifications are generally defined under IEC 60529. The contractor should verify current local wiring, outdoor-lighting, earthing, protection and inspection requirements before energising the circuit.

Isolate the power and allow the fitting to cool before maintenance. Periodically remove dust from the lens and housing with a soft, dry or lightly damp cloth, keep heat-dissipation surfaces clear and inspect the bracket, fasteners, cable glands, seals and wiring for damage or corrosion. Do not use aggressive chemicals, high-pressure cleaning at close range or open the enclosure unless permitted by the manufacturer.

Check the brand, model number PSLED FLGS50 DL and SKU 83534-NOS against the lighting schedule or purchase request. Also verify the specified 50W power, 6500K daylight colour, 220–240V AC 50/60Hz input, IP65 rating and non-dimmable operation. This prevents substitution with a different wattage, colour temperature, voltage or ingress-protection level.