PowerSafe LED Batten Light 20W Daylight PSLED BL20 DL

This LED batten light is suitable for compatible spaces requiring bright, cool-white general lighting, such as corridors, utility rooms, workshops, storage areas, plant rooms, site offices, garages and service areas. Suitability for a particular location must be confirmed against the required illumination level, mounting conditions, environmental exposure and project specifications.

A 6500K colour temperature produces a cool, daylight-white appearance that supports clear visibility in task-oriented and functional areas. It is commonly selected for workshops, stores, utility spaces and construction support areas where a crisp lighting effect is preferred. It may appear cooler than warm-white or neutral-white lighting, so the specified colour temperature should be checked before ordering multiple fittings.

Yes. The stated input rating of 220-240V AC at 50/60Hz is compatible with the nominal low-voltage supply commonly used in the UAE. The actual circuit voltage, protective device, cable size, earthing arrangement and connection method must still be verified by a qualified electrician in accordance with the project design and the requirements of the relevant UAE authority.

No. The PowerSafe PSLED BL20 DL is specified as non-dimmable. It should be connected to a standard compatible switched lighting circuit and not to a conventional dimmer. Using an incompatible dimming control may cause flickering, unstable operation or product damage.

Installation should be performed by a qualified electrician. Isolate and verify the electrical supply, confirm that the circuit is rated for 220-240V AC, securely fix the batten to a suitable mounting surface, and connect the conductors according to the product markings and supplied instructions. Restore power only after checking terminal security, cable protection, earthing requirements and the completed installation. The installer should also maintain safe clearances and avoid covering the fitting unless expressly permitted by the manufacturer.

Contractors should verify the model number PSLED BL20 DL, 20W connected load, 6500K colour temperature, non-dimmable operation and 220-240V AC supply rating. They should also confirm the required quantity through the lighting design, check mounting and cable-entry conditions, coordinate switching arrangements, and ensure compliance with approved drawings, project specifications and applicable requirements of authorities such as DEWA, ADDC, SEWA or the relevant local utility and municipality.

Outdoor suitability cannot be confirmed from the provided specifications because no IP weather-resistance rating is stated. Do not install it where it may be exposed to rain, water, condensation, heavy dust or direct weather unless the manufacturer confirms an appropriate IP rating for that environment. For external UAE applications, select a fitting with a documented ingress-protection rating suited to the installation conditions.

Use in dusty, humid or splash-prone locations depends on the fitting's verified IP rating and the environmental requirements of the project. As an IP rating is not provided in the available product data, buyers should not assume that the fitting is dustproof or water-resistant. Confirm suitability before installation or choose a protected batten specifically rated for harsh conditions.

The required quantity depends on room dimensions, mounting height, surface reflectance, task type, spacing, obstructions and the target illuminance in lux. The 20W power rating alone does not establish light output or coverage. For construction and commercial projects, a lighting calculation should be completed using verified photometric data and the illuminance requirements stated in the approved design or relevant lighting guidance.

It may replace a compatible fluorescent batten where the electrical supply, physical mounting, light distribution, required illumination and environmental rating are suitable. It is not necessarily a direct component-for-component retrofit into an existing fluorescent body. A qualified electrician should remove or safely isolate obsolete control gear and install the LED batten according to the manufacturer's instructions.

Each fitting has a stated nominal power of 20W, which should be included in the lighting circuit's connected-load schedule. For multiple units, add the rated wattage of all fittings and account for applicable driver characteristics, switching arrangements, cable capacity and protective-device requirements. Final circuit design must follow the project electrical calculations and relevant UAE regulations.

The supplied specifications do not identify this model as an emergency or battery-backed luminaire. It should not be treated as emergency lighting unless an approved, compatible emergency system and the required certification are confirmed by the manufacturer and project consultant. UAE projects should use designated emergency luminaires that satisfy the approved fire-and-life-safety design.

Periodically isolate the power and clean the external surface with a soft, dry or lightly damp cloth, following the manufacturer's guidance. Do not use abrasive cleaners, solvents or direct water spray. Inspect the fitting for loose mounting, damaged wiring, discoloration, moisture ingress or flickering, and have any electrical fault assessed by a qualified electrician.

Check the brand, model and key specifications before ordering: PowerSafe PSLED BL20 DL, 20W LED batten, 6500K daylight, 220-240V AC, 50/60Hz and non-dimmable operation. For project procurement, compare these details with the approved material submittal, lighting schedule and required quantity to avoid mixing different wattages or colour temperatures.