PowerSafe LED Bulb 12W Daylight B22 PSLEDB 1222 DL

Key specifications include a rated power of 12W, B22 bayonet cap, 6500K daylight colour temperature and 220-240V AC operation at 50/60Hz. The bulb has a standard shape and is non-dimmable. Buyers should use the model reference PSLEDB 1222 DL to confirm an exact product match.

Yes. Its stated 220-240V AC, 50/60Hz input is compatible with the nominal low-voltage supply commonly used in the UAE. The lamp holder, circuit protection, wiring and installation method must also comply with the requirements of the relevant local authority, such as DEWA, EtihadWE, SEWA or ADDC, depending on the project location.

A 6500K colour temperature produces a crisp, cool-white daylight appearance. This light colour is often selected for task-oriented spaces such as utility rooms, workshops, storage areas, site offices, kitchens and commercial back-of-house areas. Buyers wanting a softer or warmer ambience should choose a bulb with a lower colour-temperature rating.

This bulb requires a compatible B22 bayonet-cap lamp holder. A B22 fitting uses side pins that are inserted into the holder and secured with a short twist. It is not directly compatible with E27 screw-type holders, so contractors should verify the installed holder before procurement or replacement.

Isolate the lighting circuit at the distribution board and confirm that the power is off. Allow any existing lamp to cool before removal. Check that the holder is undamaged, dry and rated for a B22 lamp and 220-240V AC supply. Align the bulb's side pins with the holder slots, push it in gently and twist until secure. Restore power and test operation. Fixed wiring or damaged holders should only be handled by a qualified electrician in accordance with applicable UAE electrical requirements.

No. The PSLEDB 1222 DL is specified as non-dimmable. It should be connected to a standard on-off lighting circuit rather than a conventional dimmer, electronic dimming module or variable-voltage control. Using an incompatible dimmer may cause flickering, unstable operation or premature product failure.

It can be used for general illumination in compatible residential, commercial and light-duty construction settings, including rooms, corridors, stair areas, stores, maintenance spaces, workshops, temporary site offices and accommodation units. Suitability depends on the lighting level required, the B22 holder and the environmental conditions at the installation point.

It may be used in enclosed and properly wired site offices, welfare facilities, storage rooms or other protected fittings operating at 220-240V AC. It should not be treated as a rugged portable site light unless installed in a suitable protective luminaire. Construction environments may require impact protection, dust or moisture resistance, guards and other measures determined by the project's electrical and HSE requirements.

The supplied information does not state an IP weather-resistance rating for the bulb. For outdoor use, it should therefore be installed only inside a compatible enclosed weatherproof luminaire with an IP rating appropriate to the exposure level. Protection from rain, irrigation water, dust, humidity and direct environmental exposure is especially important in UAE gardens, parking areas and building exteriors.

Contractors should calculate the connected lighting load using the 12W nominal rating per bulb, confirm the circuit voltage and frequency, and verify cable sizing, protective devices, switching equipment and lamp-holder ratings. LED driver inrush current and the manufacturer's switching limitations should also be considered when many lamps are operated together. Circuit design and installation should follow the relevant project specifications and UAE authority requirements.

The product is rated for direct connection through a compatible B22 holder to a 220-240V AC, 50/60Hz supply. A separate low-voltage transformer is therefore not indicated. It must not be connected to a 12V or 24V lighting circuit unless a correctly designed system supplies the bulb with its specified input.

Check that the existing lamp uses a B22 bayonet cap, the circuit supplies 220-240V AC at 50/60Hz and a 12W non-dimmable LED is suitable for the fitting. Also confirm that the desired light colour is 6500K daylight and that the bulb's standard shape fits physically inside the luminaire. For exact identification, match the PowerSafe model number PSLEDB 1222 DL.

Possible causes include an incompatible dimmer, a loose or damaged B22 holder, incorrect supply voltage, poor wiring connections or a faulty switch. Isolate the circuit before checking the bulb's seating. If the issue continues, test the lamp only in a known-compatible fitting or ask a qualified electrician to inspect the circuit; do not work on live electrical components.

Switch off and isolate the circuit before cleaning or inspection, and allow the bulb to cool. Remove dust using a dry, soft cloth without applying water, solvents or abrasive cleaners. Periodically check the holder and luminaire for looseness, heat damage, corrosion or dust accumulation. Replace damaged electrical components through a qualified electrician.