PowerSafe LED Bulb 9W Daylight B22 PSLEDB 0922 DL

Its key specifications are a 9W nominal power rating, B22 bayonet cap, 6500K daylight colour temperature, and 220–240V AC operation at 50/60Hz. It uses LED lighting technology, has a standard bulb shape, and is non-dimmable. Lumen output, beam angle, rated lifetime, IP rating, and power factor are not stated in the supplied specifications and should be confirmed if they are critical to the lighting design.

This bulb is suitable for compatible general-lighting installations in homes, offices, shops, workshops, storerooms, corridors, site offices, and construction accommodation. Its 6500K cool white light is commonly selected for functional areas where a bright, crisp visual appearance is preferred. Suitability ultimately depends on the required illumination level, luminaire design, ventilation, and site conditions.

It can be used for general lighting in enclosed site offices, temporary accommodation, stores, maintenance rooms, and similar locations fitted with suitable B22 holders. For active work zones, lighting calculations and site safety requirements should determine the required lumen output, fixture protection, mounting position, and number of lamps. Do not use the bare bulb where impact, dust, water, or harsh weather exposure requires a protected construction-site luminaire.

Switch off and isolate the electrical supply, allow the existing lamp to cool, and confirm that the holder is a compatible B22 bayonet type. Align the bulb's side pins with the holder slots, press inward gently, and rotate until it locks securely. Restore power only after confirming that the bulb is properly seated. Installation and electrical maintenance should be completed by a qualified person in accordance with applicable UAE authority and wiring requirements.

It can replace a lamp only when the existing fitting uses a B22 holder and is compatible with a 220–240V AC LED bulb. Buyers should also verify the bulb's physical clearance, desired 6500K colour appearance, luminaire ventilation, control equipment, and required light output. Wattage alone does not establish equivalent brightness, so confirm lumen requirements where illumination performance is important.

Yes. Its stated input rating of 220–240V AC at 50/60Hz is compatible with the nominal low-voltage supply commonly used in the UAE. The circuit, lamp holder, protective devices, and installation method must still be suitable for the product and comply with the requirements of the relevant local authority, project consultant, and applicable UAE electrical regulations.

No. This model is specified as non-dimmable and should not be connected to a conventional dimmer, even if operated at maximum output. An incompatible dimmer may cause flickering, unstable operation, noise, premature failure, or failure to illuminate. Use it with a standard on/off lighting circuit and compatible controls.

A 6500K colour temperature produces a cool white, daylight-style appearance rather than the softer yellow tone associated with warm white lamps. It is often preferred in workshops, utility rooms, storage areas, kitchens, offices, and task-oriented spaces. Colour temperature describes the appearance of the light and does not indicate brightness, wattage, or colour-rendering performance.

Outdoor use should only be considered when the bulb is installed inside a compatible weather-protected luminaire with an appropriate IP rating for the location. The bulb itself has no stated IP rating in the supplied specifications, so it should not be exposed directly to rain, irrigation water, condensation, sand, or dust. For UAE outdoor conditions, also check the enclosure's temperature rating and ventilation.

Contractors should verify the B22 base, 220–240V AC supply, 9W connected load, non-dimmable circuit requirement, 6500K light colour, luminaire dimensions, ventilation, and environmental protection. The required lux level, lumen output, emergency-lighting compatibility, power factor, colour-rendering index, operating temperature, and rated lifetime should be confirmed separately where these form part of the project specification or consultant approval.

The required quantity depends on room dimensions, mounting height, surface reflectance, luminaire efficiency, spacing, and the target illuminance in lux. Because the bulb's lumen output and beam distribution are not stated, an accurate quantity cannot be calculated from wattage alone. For construction, commercial, or workplace applications, use verified photometric data and a lighting calculation prepared against the project's illumination requirements.

Common causes include an incorrectly seated B22 cap, a loose or damaged holder, unstable supply voltage, incompatible dimmer or electronic control, defective wiring, or a switched circuit that allows small leakage currents. Isolate the supply before checking the fitting and never work on an energised holder. If the issue continues, have a qualified electrician inspect the circuit and confirm compatibility.

Switch off and isolate the supply, allow the bulb to cool, and clean it gently with a dry, soft cloth. Do not spray water or cleaning chemicals onto the bulb or lamp holder. Dust accumulation around an enclosed fitting can reduce heat dissipation, so inspect the luminaire periodically and keep ventilation openings clear while following the fixture manufacturer's maintenance instructions.

Check for the full product name PowerSafe LED Bulb 9W Daylight B22, model PSLEDB 0922 DL, and SKU 83366-NOS. Confirm that the existing fitting accepts a B22 bayonet cap, the circuit supplies 220–240V AC at 50/60Hz, a 6500K daylight appearance is required, and no dimming function is needed.