PowerSafe LED Floodlight 100W Daylight PSLED FL100 DL

This floodlight is suitable for compatible applications such as construction-site areas, building perimeters, warehouses, workshops, loading areas, parking spaces, compounds, gardens and villa exteriors. The installer should confirm that its light distribution, mounting position and environmental rating meet the requirements of the intended location.

Its IP65 rating makes the correctly installed enclosure dust-tight and resistant to water jets, supporting many outdoor applications. It must not be submerged, and all cable entries, junction boxes, glands and connections must provide suitable weather protection. In exposed UAE locations, position it to limit water accumulation and excessive heat around the fitting.

A 6500K colour temperature produces a cool, crisp white light commonly described as daylight. It can improve general visibility in work areas, construction zones, yards and security-lighting applications. Buyers seeking a warm or neutral ambience should note that this model has a distinctly cool-white appearance.

The PSLED FL100 DL is rated for 220-240V AC at 50/60Hz, with a stated rated current of 430mA. Its nominal 100W load should be included when calculating circuit capacity, cable sizing, protective-device selection and the combined demand of multiple floodlights.

Isolate and verify the electrical supply before installation. Secure the floodlight bracket to a structurally sound surface using fixings suitable for the substrate, aim the fitting without straining the bracket, and complete the wiring according to the manufacturer's instructions. Weatherproof glands and suitably rated junction boxes should be used outdoors. Installation should be performed by a qualified electrician in accordance with applicable UAE authority requirements.

Fixings must suit both the substrate and the fitting load. Use appropriate anchors for sound concrete, approved fixings for masonry and suitable corrosion-resistant fasteners for steelwork. Do not rely on weak plaster, cladding or unsupported block edges. Contractors should also check drilling zones for concealed electrical services, pipes and structural reinforcement before fixing.

No. This model is specified as non-dimmable and should not be connected to a conventional dimmer. If automatic operation is required, use a compatible photocell, timer, contactor or occupancy-control arrangement that is correctly rated for LED loads and any associated inrush current.

Multiple units may be used where the circuit design permits, but the electrician must calculate the total connected load, cable capacity, voltage drop, switching capacity and protective-device rating. LED-driver inrush current should also be considered, particularly in larger construction, warehouse or perimeter-lighting installations.

IP65 indicates complete protection against dust ingress and protection against water jets when the floodlight is correctly assembled and installed. It does not mean the unit is suitable for immersion, pressure washing at close range or use with unprotected electrical connections. The complete installation must maintain suitable ingress protection, not only the light fitting.

The stated rated lifetime is 25,000 hours under the manufacturer's specified operating conditions. Actual service life can vary with ambient temperature, daily operating hours, switching frequency, supply quality, ventilation, installation orientation and exposure to dust, salt or moisture.

Its 220-240V AC, 50/60Hz rating is compatible with commonly used UAE low-voltage supplies, while its 100W output class, 6500K daylight colour and IP65 enclosure suit many worksite, commercial and residential exterior-lighting needs. Final selection and installation should comply with the project's specifications and the requirements of the relevant UAE electricity and building authority.

It can support compatible temporary site-lighting arrangements when securely mounted and connected through a properly designed electrical system. The installation should include suitable earthing where required, circuit protection, weatherproof connections and cable routing protected from vehicles, sharp edges and standing water. Temporary installations must still follow site safety rules and applicable UAE electrical requirements.

Mount it at a stable height and angle that spreads light across the target area while reducing glare into neighbouring properties, roads, windows and workers' direct lines of sight. Avoid covering the fitting or placing it where ventilation is restricted. For larger areas, several properly spaced floodlights may provide more uniform illumination than one fitting aimed from a single point.

Switch off and isolate the supply before maintenance. Periodically remove dust and dirt from the lens and housing using a soft, dry or lightly damp cloth, and inspect the bracket, fasteners, cable glands, seals and wiring for damage or corrosion. Do not use abrasive cleaners or high-pressure water. A damaged enclosure, cable or seal should be assessed by a qualified electrician.