PowerSafe LED Floodlight 30W Daylight PSLED FL30 DL

Key specifications include 30W rated power, 3000 lm luminous flux, 6500K daylight colour temperature, 220–240V AC input, 50/60Hz frequency, 130 mA rated current, IP65 ingress protection, non-dimmable operation, and a stated rated lifetime of 25,000 hours under the manufacturer's specified operating conditions. The model reference is PSLED FL30 DL.

The floodlight provides a stated output of 3000 lumens from 30W of power, equivalent to approximately 100 lumens per watt. Actual illumination at the working surface depends on mounting height, aiming angle, spacing, surrounding surfaces, and the size of the area being lit. A lighting calculation is recommended for construction sites and other applications with defined lux requirements.

This floodlight is suitable for compatible applications such as villa entrances, gardens, boundary walls, driveways, parking areas, workshops, warehouses, building perimeters, loading zones, service areas, and selected construction-site locations. The installer should confirm that its light output, mounting position, environmental conditions, and electrical rating meet the requirements of the project.

Its IP65 rating makes it suitable for many exposed outdoor locations when the floodlight, cable entry, junction box, glands, seals, and mounting arrangement are installed correctly. IP65 indicates protection against dust ingress and water jets, but it does not make the unit suitable for immersion, flooding, or underwater installation. For UAE outdoor use, avoid locations where water can collect and verify that the operating environment remains within the manufacturer's permitted temperature conditions.

A 6500K colour temperature produces a cool, crisp white appearance commonly described as daylight. It can support visibility in work yards, access routes, loading areas, security zones, and construction-related spaces where clear general illumination is preferred. It is cooler in appearance than warm-white or neutral-white lighting and may not suit areas intended to create a soft or decorative ambience.

Installation should be completed by a qualified electrician. Isolate and verify the electrical supply before work begins, secure the mounting bracket to a structurally sound surface with fixings suitable for the substrate, aim the floodlight without obstructing heat dissipation, and connect it to a compatible 220–240V AC, 50/60Hz circuit. Use appropriately rated outdoor cable, glands, junction boxes, earthing arrangements, and protective devices, then restore power and test the installation. Always follow the manufacturer's instructions and applicable UAE authority requirements.

Confirm that the mounting surface can support the fitting and withstand wind, vibration, and maintenance loads. Select anchors for the actual substrate, such as approved concrete anchors, suitable blockwork fixings, or corrosion-resistant fasteners for steel. Check for concealed electrical services, pipes, reinforcement, and waterproofing membranes before drilling. The bracket should be firmly secured, and external penetrations should be sealed with a weather-compatible system where required.

No. The PSLED FL30 DL is specified as non-dimmable and should not be connected to a conventional lighting dimmer. It should be operated using compatible on/off switching and control equipment. If a timer, photocell, contactor, or occupancy sensor is planned, an electrician should verify its voltage rating, switching capacity, LED-load compatibility, and suitability for the installation environment.

It may be used for compatible fixed lighting applications on construction sites, subject to the project's lighting design, risk assessment, electrical distribution system, and local safety requirements. Its 220–240V AC rating must match the available circuit. On sites where reduced-voltage equipment, temporary-lighting systems, impact-resistant fittings, emergency lighting, or specific lux levels are required, the project engineer should confirm suitability before installation.

No. IP65 is the stated enclosure rating of the floodlight under the relevant test conditions. The completed installation is only as weather-resistant as its weakest component. Cable joints, glands, connectors, isolators, junction boxes, seals, and wall penetrations must have suitable ingress-protection ratings and be correctly fitted to maintain protection in dusty or wet UAE environments.

The required quantity depends on the target lux level, area dimensions, mounting height, beam distribution, spacing, surface reflectance, obstructions, and the level of uniformity required. The stated 3000 lm output can be used as an input for a lighting calculation, but lumen output alone does not determine coverage. Warehouses, work areas, access roads, and construction zones should be designed against the project's specified illumination criteria.

Mount the unit where air can circulate around it, keep heat-dissipating surfaces free from heavy dust, avoid covering the floodlight, and prevent exposure to standing water or corrosive chemicals. Periodically isolate the circuit and inspect the bracket, seals, cable glands, enclosure, and electrical connections. The stated 25,000-hour lifetime is based on the manufacturer's operating conditions and can be affected by ambient heat, supply quality, switching frequency, contamination, and installation quality.

IP65 describes dust and water protection but does not by itself confirm resistance to salt-laden air or marine corrosion. For installations near the UAE coastline, assess the housing, bracket, fasteners, cable glands, and junction boxes for corrosion resistance. Regular inspection and suitable corrosion-resistant accessories may be required, particularly in exposed seafront or industrial environments.

The circuit should include correctly selected overcurrent protection, isolation, earthing where required, and residual-current protection where mandated by the installation location and applicable regulations. Cable size and protective-device ratings must be determined from the circuit design, installation method, fault level, voltage drop, and connected load rather than from the floodlight wattage alone. A qualified electrician should install and test the circuit in accordance with applicable UAE utility and building requirements.