PowerSafe LED Spotlight 7W Daylight GU10 PSLED GU1007 DL

Key specifications include 7W rated power, 630 lm luminous flux, 6500K daylight output, GU10 cap, 220–240V AC input, 50/60Hz frequency, 56 mA rated current and IP20 protection. The lamp is non-dimmable and has a manufacturer-stated rated lifetime of 15,000 hours under specified operating conditions.

This LED spotlight is suitable for compatible indoor ceiling spotlights, recessed downlights and directional light fittings. Typical applications include homes, offices, shops, reception areas, corridors, workshops, storerooms and selected indoor construction or fit-out spaces where cool daylight illumination is required.

Yes. The 6500K output produces a cool, bright daylight appearance that is commonly selected for task-oriented spaces such as offices, workshops, retail displays, utility rooms and building service areas in the UAE. Project engineers should still confirm that the colour temperature, illumination level and visual-comfort requirements match the lighting design.

The lamp is rated for 220–240V AC at 50/60Hz, which aligns with commonly used low-voltage building supplies in the UAE. Compatibility must also be checked at the GU10 lamp holder, circuit, protective device and control level. Installation should follow the manufacturer's instructions and applicable requirements of the relevant UAE electrical authority.

Switch off and isolate the electrical supply, verify that the fitting uses a GU10 holder and confirm that the fitting voltage matches the lamp's 220–240V AC rating. Insert the GU10 pins into the holder and rotate the lamp until securely locked, following the fitting manufacturer's instructions. Restore power only after checking that the lamp is correctly seated. Fixed wiring and fitting work should be completed by a qualified electrician.

It can replace a lamp where the existing fitting has a compatible GU10 holder, accepts a 220–240V AC LED lamp and provides adequate physical clearance and ventilation. Buyers should compare the cap type, supply voltage, wattage, dimensions, light output, colour temperature and dimming arrangement before replacement. Do not install it in a low-voltage MR16 or GU5.3 holder.

No. The PSLED GU1007 DL is specified as non-dimmable. It should not be connected to a dimmer unless the complete control arrangement has been explicitly confirmed as compatible by the manufacturer. For standard operation, use a conventional on/off switching circuit.

IP20 indicates protection against access by fingers and solid objects larger than 12.5 mm, but it does not provide protection against water. The lamp is therefore intended for dry indoor installations in a suitable fitting. It should not be used in exposed outdoor locations, wet areas or zones subject to water spray unless housed within an appropriately rated enclosure designed for that environment.

The lamp itself is rated IP20, so it is not suitable for direct exposure to rain, irrigation water, dust-heavy environments or outdoor humidity. Any proposed outdoor use would require a fully compatible weatherproof luminaire with an ingress-protection rating appropriate to the site. The installer must also consider UAE heat, dust and moisture conditions and follow local electrical requirements.

The required quantity depends on room dimensions, ceiling height, surface reflectance, fitting layout, target lux level and the activities performed in the space. Each lamp is listed at 630 lumens, but a lighting calculation should account for luminaire efficiency, spacing, maintenance factors and obstructions. Contractors should use the project's approved lighting design rather than selecting lamp quantities by wattage alone.

Contractors should verify the PSLED GU1007 DL model reference, GU10 base, 220–240V AC supply, 7W connected load, 630 lm output, 6500K colour temperature, non-dimmable operation and IP20 rating. They should also confirm fitting compatibility, required illumination levels, circuit capacity, installation environment and compliance with project specifications and applicable UAE authority requirements.

The nominal 7W power rating allows engineers and electricians to estimate the connected lighting load by multiplying 7W by the number of lamps on the circuit. Circuit planning must also consider switching arrangements, driver inrush characteristics, cable capacity, protective devices and any project-specific diversity assumptions. Final calculations should be completed by a competent electrical professional.

The manufacturer lists a rated lifetime of 15,000 hours under specified operating conditions. Actual service life can vary with ambient temperature, daily operating hours, switching frequency, supply quality, fitting ventilation and installation conditions. Using the lamp in a suitable GU10 fitting and avoiding excessive heat can support reliable performance.

Isolate the power before inspection or cleaning, allow the lamp to cool and remove dust using a soft, dry cloth. Do not use water, solvents or abrasive cleaners. During planned maintenance, check the holder for looseness, heat damage or corrosion and replace damaged fittings through a qualified electrician. In dusty UAE environments, periodic cleaning can help preserve useful light output.