PowerSafe LED Spotlight 7W Daylight PSLED SL07 DL

The principal specifications are a rated power of 7W, a 6500K daylight colour temperature, and a 220-240V AC operating range at 50/60Hz. The product uses LED lighting technology and is non-dimmable. Its model number is PSLED SL07 DL, which should be checked when matching the spotlight to project schedules, replacement requirements, or compatible fittings.

This spotlight can be used in compatible fittings for focused illumination in homes, shops, offices, corridors, display areas, workshops, utility rooms, and suitable construction project interiors. Its 6500K daylight output is useful where a crisp, cool white appearance is required. Application suitability depends on the fitting, room conditions, required light level, and the electrical design.

A 6500K colour temperature creates a cool, daylight-like appearance that can support visual clarity in work areas, utility spaces, inspection points, workshops, and other task-oriented environments. Contractors should still confirm that the proposed quantity, positioning, beam distribution, and overall lighting design meet the illumination requirements of the space.

Yes. Its stated input of 220-240V AC at 50/60Hz is compatible with the commonly used low-voltage electrical supply range in the UAE. The circuit, fitting, wiring, isolation method, and protective device must nevertheless be suitable for the product and installed in accordance with applicable UAE authority requirements and project specifications.

Switch off and isolate the electrical circuit before installation. Confirm that the supply voltage and light fitting are compatible, inspect the product for damage, and install it securely according to the fitting and manufacturer instructions. Restore power only after all connections and components have been checked. Fixed electrical work should be completed by a qualified electrician.

Verify the model number, 7W rating, 6500K colour temperature, 220-240V AC supply, physical dimensions, fitting type, available installation space, and environmental conditions. The supplied data does not state the lamp cap, beam angle, dimensions, lumen output, or IP rating, so these details should be confirmed before ordering for a specific fitting or project.

No. The PSLED SL07 DL is specified as non-dimmable and should not be connected to a dimming control unless the manufacturer explicitly confirms compatibility. Use it with a standard compatible switching circuit, as an unsuitable dimmer may cause flickering, unstable operation, reduced service life, or damage.

Outdoor suitability cannot be confirmed from the available specifications because no IP protection rating is stated. Do not expose the spotlight directly to rain, water, dust, or severe outdoor conditions unless its enclosure and fitting are confirmed as suitable for that environment. For external installations, select an appropriately IP-rated fitting and follow UAE project and authority requirements.

Installation in bathrooms, wash areas, or damp locations depends on the fitting's verified IP rating, its placement within the relevant electrical zone, and local wiring requirements. Because an IP rating is not provided in the listed product data, suitability for wet or damp areas should be confirmed before installation.

Use the nominal 7W rating as the basic connected load per spotlight. For example, ten units represent a nominal lamp load of 70W. The electrical designer should also consider the driver characteristics, starting current where applicable, circuit capacity, cable selection, protective devices, switching equipment, and any project-specific load allowances.

The required quantity depends on the room dimensions, ceiling height, surface reflectance, fitting position, beam angle, lumen output, target lux level, and intended activity. Since lumen output and beam angle are not stated, a precise lighting calculation cannot be made from wattage alone. Contractors should obtain the necessary photometric data or prepare a lighting layout before finalising quantities.

Installation should follow the manufacturer's instructions, the approved project drawings, and the requirements of the relevant UAE authority, such as DEWA, ADDC, SEWA, or the authority serving the project location. A qualified person should verify circuit isolation, conductor and protective-device suitability, earthing requirements where applicable, and compatibility with the selected light fitting.

Isolate the power and allow the spotlight to cool before inspection or cleaning. Remove surface dust with a soft, dry cloth and avoid water, solvents, or abrasive cleaners. Check periodically for flickering, discoloration, overheating, loose fitting components, or physical damage. A faulty or damaged unit should be replaced rather than opened or modified.

Match the product name and model number PSLED SL07 DL with the lighting schedule or existing unit. Also verify the 7W wattage, 6500K daylight colour, 220-240V AC operating range, non-dimmable specification, and fitting compatibility. The SKU 83697-NOS can help identify the product when searching or ordering from FEPY.com in the UAE.