PowerSafe Neon LED Strip Light 8W Warm White Single Line 100m Roll PSLED SLNS 08W 1L WW 100M

This strip produces warm white light at a specified colour temperature of 3000K. The softer, warmer tone is commonly selected for villas, hotels, restaurants, majlis areas, landscaped spaces, reception areas and decorative architectural details. Buyers should confirm that 3000K matches the approved lighting schedule or project specification.

The listed nominal power rating is 8W. Before sizing a driver, power supply, cable or protective device, the installer must confirm from the product label and technical documentation whether this rating applies per metre, per section or to another defined unit. The total connected load should then be calculated from the installed length, with suitable capacity allowance as required by the driver manufacturer.

Do not assume that the full 100m roll can be powered from a single connection. Maximum run length depends on the strip voltage, conductor capacity, voltage drop, driver rating and the manufacturer's connection limits. Long construction runs may require approved sectional wiring, additional power feeds or separate drivers to maintain consistent brightness and prevent overheating.

A compatible power supply or LED driver may be required, depending on the strip's rated input shown on its label or installation sheet. The output voltage, current capacity, wattage, control method and environmental rating of the driver must match the strip. Never connect the roll directly to a supply voltage unless the manufacturer specifically identifies it as suitable for that connection.

The listed product specification identifies this model as non-dimmable. It should therefore be used with compatible non-dimming control equipment unless PowerSafe provides written confirmation of an approved dimming arrangement. Connecting an incompatible dimmer can cause flickering, unstable operation, reduced service life or equipment damage.

Subject to the approved design and environmental rating, it can be considered for linear accent lighting, ceiling coves, recessed details, corridors, reception counters, shopfitting, façade features, signage surrounds, staircase details and landscape structures. Contractors should coordinate the strip route, access points, driver locations and control circuits with the architectural, electrical and joinery drawings.

Outdoor suitability cannot be confirmed from the available specifications because an IP rating and operating-temperature range are not stated. For façades, gardens, balconies or other exposed UAE locations, verify the required IP rating, UV resistance, ambient-temperature limit and connector sealing before installation. Drivers and joints must also have appropriate protection from dust, rain, irrigation water and condensation.

Plan and measure the route first, then prepare a clean, dry and stable mounting surface. Use only compatible channels, clips, connectors, end caps and sealants, and observe the specified bending direction and minimum bend radius. Cut the strip only at manufacturer-marked points, terminate each section correctly and test it before closing ceilings, joinery or access panels. Final electrical connection should be completed by a qualified electrician.

It may only be cut if the product carries clearly marked cutting points or the manufacturer supplies an approved cutting schedule. Cutting elsewhere can interrupt the circuit, damage the strip or compromise its sealing. After cutting, use the correct connector and end-cap system, and restore the required environmental protection before energising the installation.

The mounting detail should provide mechanical support, heat management, cable protection and access for maintenance. Avoid sharp bends, twisting, crushing, unsupported spans and contact with rough edges or wet materials. Drivers and connection points should remain accessible rather than being permanently concealed inside gypsum ceilings, wall cavities or fixed joinery.

Long runs can experience voltage drop, which may cause reduced brightness or uneven colour along the strip. The electrician should calculate the load and voltage drop using the confirmed input voltage, installed length, cable size and feed arrangement. Where necessary, divide the installation into approved sections or provide additional feeds without exceeding the manufacturer's maximum run length.

Installation should be carried out by a qualified electrical professional in accordance with the product instructions, the approved project design and the requirements of the relevant UAE authority, such as DEWA, ADDC, SEWA or the applicable local utility. Correct isolation, circuit protection, cable sizing, earthing where applicable, enclosure selection and accessible maintenance arrangements should be provided.

Yes, 3000K is commonly used where a comfortable and welcoming atmosphere is preferred, including villas, hotel rooms, restaurants, lounges, majlis spaces and premium retail interiors. For offices, workshops or task-focused zones, the project lighting designer may specify a cooler colour temperature instead. Always follow the approved lighting schedule for colour consistency.

Store the roll in its original packaging in a clean, dry and shaded location, away from direct sunlight, water, chemicals, sharp objects and excessive heat. Keep it coiled without crushing or kinking it, and unroll only the length needed for installation. Before use, inspect the strip, conductors and accessories for transport or site damage.