PowerSafe Round LED Ceiling Light 18W Daylight PSLEDR CL18 DL

The specified ratings are 18W nominal power, 6500K daylight colour temperature and 220-240V AC operation at 50/60Hz. It uses LED lighting technology and is identified by model number PSLEDR CL18 DL and SKU 83682-NOS. These details should be checked against the lighting schedule, circuit voltage and installation requirements before procurement.

This LED ceiling light can be considered for compatible indoor areas such as corridors, kitchens, utility rooms, offices, shops, workshops, stairways and building service spaces. Its 6500K output is particularly useful where a bright, cool-looking light is preferred. Suitability for bathrooms, outdoor areas or dusty locations must be confirmed from the product's IP rating and project specifications before installation.

Yes. Its stated 220-240V AC, 50/60Hz input is compatible with the standard low-voltage supply commonly used in UAE buildings. The actual circuit voltage, earthing, protective device and wiring arrangement must still be checked on site by a qualified electrician in accordance with applicable UAE authority requirements and the project's approved electrical design.

A 6500K colour temperature produces a cool white, daylight-style appearance. It can support clear visibility in task-oriented spaces, circulation areas, utility rooms and workplaces. It looks cooler and less warm than 3000K warm-white lighting, so designers should confirm that it matches the required ambience and the colour temperature of adjacent fittings.

No. The listed product specification identifies this model as non-dimmable. It should be connected to a standard compatible on/off lighting circuit rather than a conventional dimmer. Using an unsuitable dimmer may cause flickering, unstable operation or damage, so a different dimmable model should be selected where lighting-level control is required.

First isolate and verify the electrical supply, then confirm that the ceiling surface, mounting arrangement and wiring are suitable for the fitting. Secure the light using the manufacturer-approved fixing method, connect the conductors according to the supplied instructions, ensure that no copper is exposed, and refit all covers before restoring power. Installation should be performed by a qualified electrician; the exact mounting steps and required cut-out, if any, must be confirmed from the product instructions before construction work begins.

Contractors should verify the model number, 18W connected load, 6500K colour temperature, 220-240V supply, physical dimensions, mounting method, ceiling compatibility and required quantity. They should also confirm lumen-output requirements, IP rating, emergency-lighting requirements, fire-rating provisions, photometric calculations and compatibility with the project's approved material submittal. Any specification not listed should be confirmed before bulk ordering.

Each fitting has a nominal connected load of 18W. Electrical engineers can use this figure to calculate the approximate total lighting load by multiplying 18W by the number of fittings, while also accounting for driver characteristics and design margins. Circuit loading, cable sizing, voltage drop, switching capacity and protective-device selection must follow the approved design and applicable UAE electrical regulations.

It may be installed only where the ceiling construction can accept the fitting's specified mounting method and weight. Gypsum-board installations may require suitable anchors or backing support, while concrete ceilings require compatible plugs and fixings; suspended ceilings may need independent support rather than relying only on the ceiling tile. Confirm the product dimensions and mounting instructions before preparing openings or fixing points.

Outdoor or wet-area suitability cannot be confirmed without a declared IP rating. Do not install the fitting where it may be exposed to rain, water jets, condensation, excessive dust or high humidity unless the manufacturer's documentation confirms the required protection level. For UAE outdoor applications, select a fitting with an IP rating and temperature range appropriate to the site's heat, dust and moisture conditions.

Installation should comply with the relevant requirements of the local electricity authority, the approved project drawings and applicable UAE electrical and building regulations. The circuit should include appropriate isolation, protection, wiring and earthing where required by the fitting's construction. For regulated projects, contractors should also follow consultant approvals, civil defence requirements where applicable and manufacturer instructions.

Switch off and isolate the electrical supply before inspection or cleaning. Remove surface dust with a soft, dry cloth and avoid abrasive cleaners, solvents or direct water spray. Periodically check for loose mounting points, discolouration, flickering, overheating or damaged wiring, and have faults assessed by a qualified electrician rather than opening or modifying the LED assembly.

Match the required item against the full reference PowerSafe Round LED Ceiling Light 18W Daylight, model PSLEDR CL18 DL, SKU 83682-NOS. Confirm the 18W rating, 6500K daylight output, non-dimmable operation and 220-240V AC, 50/60Hz supply. For replacement projects, also compare the dimensions, mounting arrangement and electrical connection with the existing fitting before ordering.