PowerSafe Standard LED Strip Light 11W Warm White Double Line 100m Roll PSLED SLSS 11W 2L WW 100M

This LED strip produces 3000K warm white light. The warm tone creates a comfortable appearance and is commonly selected for villas, apartments, hotels, restaurants, reception areas, corridors, decorative ceilings and other spaces where softer illumination is preferred over cool white light.

Double-line identifies the strip configuration specified for this PowerSafe model. It is intended to provide a broader and more consistent illuminated line than a basic single-line arrangement. Actual brightness, uniformity and appearance depend on the installation profile, mounting surface, diffuser and power arrangement.

The product is listed with a nominal 11W rating, but the available specification does not state whether this value applies per metre, per section or to another defined operating length. Before calculating the total connected load, confirm the rating shown on the roll, packaging or manufacturer documentation. This is essential for selecting compatible drivers, controllers, protective devices and cable sizes.

Typical applications include cove lighting, gypsum-board ceilings, bulkheads, display units, shelves, corridors, reception areas, retail interiors, hospitality spaces and residential feature lighting. It may also support indirect illumination in construction fit-out projects. Suitability for exposed, wet, dusty or outdoor locations must be confirmed from the product's IP rating before installation.

Plan and measure the lighting route, verify the permitted cutting intervals, prepare a clean and dry mounting surface, and install the strip without twisting, stretching or sharply bending it. Use compatible connectors, channels, clips or profiles as required. Connect only to the voltage and control equipment stated on the product label, observe polarity where applicable, and test each section before closing ceilings or joinery. Electrical work should be completed by a qualified electrician.

LED strip rolls can generally be divided only at manufacturer-marked cutting points. Do not cut at arbitrary positions, as this may damage the circuit or cause a section to stop operating. Confirm the cut interval and reconnection method printed on this specific PowerSafe strip before dividing the roll, and seal any cut ends when required by the installation environment.

Use only a driver, rectifier or power connection system that matches the strip's marked input voltage, load and wiring configuration. The supply must be sized for the total installed length, with appropriate capacity allowance and protection. Because the listing does not state the operating voltage or confirm how the 11W rating is measured, these details must be checked on the product label before selecting electrical accessories.

Do not assume that the full roll can be powered from a single connection. Long LED strip runs may experience voltage drop, uneven brightness and conductor heating. The installer should follow the manufacturer's maximum-run limit and divide the installation into correctly supplied sections where necessary. Load calculations, cable sizing and connection points should be planned before installation.

This model is listed as non-dimmable. It should not be connected to a conventional dimmer unless PowerSafe specifically confirms compatibility with an approved dimming driver or controller. Using an incompatible dimmer can cause flickering, unstable operation, overheating or premature failure.

Outdoor suitability cannot be confirmed without a declared IP rating. For UAE exterior, landscape, balcony or humid-area installations, verify that the strip, connectors, end caps and power equipment have suitable protection against dust and moisture. They should also be appropriate for local heat and UV exposure. If no suitable IP rating is stated, use the strip only in a protected indoor location.

High ambient temperatures and enclosed ceiling voids can increase operating temperature and reduce LED service life. Where appropriate, mount the strip in a compatible aluminium profile that assists heat dissipation, avoid covering it with insulation, and provide ventilation around drivers and connection equipment. All components should remain within their specified operating-temperature limits.

Installation should follow the current requirements of the relevant UAE authority, such as DEWA in Dubai, ADDC or the applicable Abu Dhabi distribution authority, SEWA in Sharjah, or the local utility in other emirates. The work should also comply with project specifications and applicable UAE electrical and fire-safety requirements. A qualified electrician must verify voltage compatibility, earthing where required, cable sizing, isolation and circuit protection.

Confirm the model number PSLED SLSS 11W 2L WW 100M, required project length, 3000K colour temperature, operating voltage, interpretation of the 11W rating, cutting interval, maximum continuous run, IP rating, mounting method and compatible power components. Contractors should also check whether aluminium profiles, diffusers, connectors, end caps or separate drivers are required by the project.

Use a straight, compatible aluminium channel with an appropriate diffuser, maintain consistent spacing from reflective surfaces and avoid visible joints or abrupt direction changes. Test colour consistency and brightness before final fixing. For cove lighting, position the strip so individual LEDs are not directly visible and allow adequate distance for the light to blend evenly.